Quantum Rehab 6000 XL Скачать руководство пользователя страница 30

Страница: 30 / 51

www.quantumrehab.com

Quantum 6000 XL

V I . B A T T E R I E S A N D C H A R G I N G

BATTERIES AND CHARGING

The Quantum 6000 XL uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.

WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.

Wash hands after handling.

WARNING! Prevent injury and/or equipment damage! Do not use batteries that exceed the

recommended type and amp-hour capacity. Do not use batteries with different amp-hour capacities.

Refer to specifications table in this manual and in the manual supplied with the battery charger

for recommended type and capacities.

Charging the Batteries

The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power
chair’s performance by charging the batteries safely, quickly, and easily.

PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly

install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure

to heed could result in personal injury and/or property damage.

PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger directly

into a properly wired standard electrical outlet.

WARNING! You must recharge your power chair’s batteries with the supplied off-board battery

charger. Do not use an automotive-type battery charger.

WARNING! Prevent injury and/or equipment damage! Read the battery charging instructions in

this manual and in the manual supplied with the battery charger before charging the batteries.

WARNING! Prevent injury and/or equipment damage! Do no expose the off-board battery charger

to rain or other sources of moisture unless it has been tested for outdoor use. Refer to the manual

supplied with the battery charger for more information.

WARNING! Prevent injury and/or equipment damage! Explosive gases may be generated while

charging the batteries. Keep the power chair and the battery charger away from sources of ignition

such as flames or sparks and provide adequate ventilation when charging the batteries.

WARNING! Prevent injury and/or equipment damage! Inspect the battery charger, wiring, and

connectors for damage before each use. Contact your Quantum Rehab Specialist if damage is

found.

WARNING! Prevent injury and/or equipment damage! Do not attempt to open the battery charger

case. If the battery charger does not appear to be working correctly, contact your Quantum

Rehab Specialist.

WARNING! Prevent injury and/or equipment damage! If the off-board battery charger is equipped

with cooling slots, then do not attempt to insert objects through these slots.

WARNING! Prevent injury and/or equipment damage! Do not allow unsupervised children to play

near the power chair while the batteries are charging.

WARNING! Prevent injury and/or equipment damage! If your off-board battery charger has not

been tested and approved for outdoor use, then do not expose it to adverse or extreme weather

conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it

must be allowed to adjust to the difference in environmental conditions before use indoors. Refer

to the manual supplied with the battery charger for more information.

Содержание 6000 XL




















































Результаты поиска

Содержание 6000 XL

Отзывы:

Похожие инструкции для 6000 XL

Бренды по названию

Популярные бренды

Quantum Rehab 6000 XL, Руководство пользователя

Результаты поиска

Содержание 6000 XL

Отзывы:

Похожие инструкции для 6000 XL

Бренды по названию

Популярные бренды