manualshive.com logo in svg

Quality Water Treatment SOFTPRO ELITE, Руководство по установке, Страница: 27 / 44

Поделиться
Скачать
Quality Water Treatment SOFTPRO ELITE Скачать руководство пользователя страница 27

 

SOFTPRO INSTALLATION GUIDE 

 

 

©2022 SoftPro Water Systems. All rights reserved. 

 

27

 

.

 

 

2)

 

Install the control valve to the softener tank as follows. 

a.

 

Place the top of the distribution tube (white pipe located in the tank) through the bottom center of the upper 

basket cone.  

b.

 

Then screw on the softener control valve assembly onto the tank.  

 

HAND-TIGHTEN ONLY, DO NOT OVER-TIGHTEN.

 

Note

:  As  you  complete  this  installation  step,  the  control  valve  will  drop  into  a  socket  on  the  tank  once  the 

distribution tube clears the O-ring from the bottom of the control valve. You'll feel it drop and then just hand 

tighten.

 

 

HAND-TIGHTEN ONLY, DO NOT OVER-TIGHTEN.

 

Do not force the screwing of the control valve. It should screw on very easily. 

 

ATTENTION: 

DO NOT USE LUBRICANTS OR TEFLON TAPE.

  

The installed O-ring was previously lubricated with a non-petroleum-based lubricant. Never use Vaseline, WD-40, etc.

 

 

NOTE ON D-TUBE CENTERING: 

It is acceptable and common that the distribution tube (the white PVC pipe) in the softener 

tank is not completely centered. This is acceptable, the control valve will pull it to the center as it is screwed onto the tank.  
 

  

 

 

 

Содержание SOFTPRO ELITE













































Отзывы:

Нет отзывов