Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 9

Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 8

Page 8 of 9

Copyright © 2011 Quality Water Treatment, All right reserved.

rev. 8/2/2011

www.qualitywatertreatment.com

Programming your Prosoft system.

Enter the master programming mode by Pressing and holding the shift and up buttons
simultaneously for 5 seconds

Your programming will go as follows:

System type: 4
MTR DLY FIX RSV

Press the extra cycle button

Valve type:
56xt/6700

Press the extra cycle button

Regenerant Flow:
Down flow

Press the extra cycle button

Display format:
US Gallons

Press the extra cycle button

Unit Capacity:
Set it to the capacity that your system is

Press the extra cycle button

Water Hardness:
(Program in your hardness level)

Press the extra Cycle button

Capacity safety factor:
00%

Press the extra Cycle button

Volume override:
1000 g

Press the extra cycle button

Regeneration day Override:
14

Press the extra cycle button

Regeneration time:
2:00 a.m.

Press the extra cycle button
step 1 (BW): 10,

extra cycle button

«
...
6
7
8
9
»

Содержание Prosoft Elite










Отзывы:

Нет отзывов