Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 9

Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 1

Page 1 of 9

Copyright © 2011 Quality Water Treatment, All right reserved.

rev. 8/2/2011

www.qualitywatertreatment.com

INSTALLATION & START-UP INSTRUCTIONS

Prosoft Elite Metered WATER

SOFTENER

Thank you for your purchase of a new Prosoft Elite
Metered water softener from Quality Water Treatment!
We have put together these instructions as a reference,
and they are to be used as a general installation
guideline.

Pre-Installation Guide

Before you assembly your new system, be sure that the
following conditions have been met for placement of your

system:

Level, firm surface, such as concrete, on which to place the

softener tank and salt tank AKA Brine Tank

Nearby floor drain or standpipe to connect to the softener for use during each

regeneration

Standard US plug, 120v 60hz (the softener system includes a 5ft. power cord and plug. Be

sure the plug is not connected to a light switch

Make a list of all the plumbing fittings to completely install the unit
Typical is:

Two - 3/4" or 1” male adaptors

Eight - 90

°

elbows

Amount of pipe you need

1/2" drain line and 90

°

elbows

Adding the Resin to the Water Softener Tank

1. Position your new softener unit where you want it placed for use.

2. Inside the Softener tank you’ll find a 3/4" or 1" gray or white Pvc tube (called a

distributor tube.) If the tube does not already have a cap on the top use a pvc slip cap or

some duct tape to temporarily plug this tube (this is to keep the resin from going down the
tube.) If your system came with gravel, add the gravel first, then the resin. Use the included
special funnel when adding the resin. This will take about 10 minutes.

1
2
3
...
»

Содержание Prosoft Elite










Отзывы:

Нет отзывов