Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 9

Quality Water Treatment Prosoft Elite Скачать руководство пользователя страница 6

Page 6 of 9

Copyright © 2011 Quality Water Treatment, All right reserved.

rev. 8/2/2011

www.qualitywatertreatment.com

Slide the float assembly into the brine well shown in photo below and stick the stud into the

side hole on the brine well shown in photo below and secure it with the nut we supplied you.

Take the clear brine tubing that we supplied and slide it through the whole in the brine tank

and into the brine well.

Slip the plastic nut, and the two ferules one black and one white, over brine tubing then

push brass insert and screen into brine tubing as shown in photo below.

Insert tube into top fitting on float shown in photo below and hand tighten then snug it up

with a small wrench.

Note: no tape is required this is a compression fitting.

Take the other end of tube slide the Nut and Farrell over it and

insert sleeve in to tube. Push the tube into the side of the control
valve show in photo below. Tighten by hand then snug it up with a

small wrench.

«
...
4
5
6
7
8
...
»

Содержание Prosoft Elite










Отзывы:

Нет отзывов