Qualcast 46 cc Petrol Chainsaw Скачать руководство пользователя | Manualshive

Страница: 18 / 58

background image

16

Customer Helpline

0151 649 1500

WARNING!

The chain brake must not be tested with the chainsaw running unless strictly instructed

to do so in this manual. Failure to observe this warning may lead to serious personal injury.

WARNING!

The chain brake can only reduce the possibility of serious personal injury if it is fitted in

accordance with the instructions detailed in the Assembly Manual. If the chain brake is tampered with
or the chainsaw is not used in accordance with these operating instructions i.e. careless operation,
the risk of serious injury may still exist.

CAUTION!

If it proves difficult to move the chain brake lever into the required position, stop using

the chainsaw immediately. It should be inspected by a suitably qualified service technician.

The chainsaw is fitted with a chain brake which is designed to reduce the possibility of serious
personal injury due to kickback. The chain brake is engaged when pressure is applied to the chain
brake lever i.e. when the operator’s hand strikes the chain brake lever during kickback.

Once the chain brake is engaged, the saw chain stops moving immediately.

WARNING!

NEVER use a chainsaw which is damaged, incorrectly set or incompletely and loosely

assembled. Failure to observe this warning may lead to serious personal injury.

Step 2 - Check the Chain Brake (continued)

Preparing to Operate the Chainsaw

2a. Check the Chain Brake Disengages

Pull the chain brake lever

A

fully backwards until it ‘clicks’ into position. If the chain brake is

disengaged it should be possible to move the saw chain using a gloved hand.

If it is not possible to move the saw chain, the chain brake may be damaged. Do not use the chainsaw
until it has been inspected by a suitably qualified technician.

2b. Check the Chain Brake Engages

Push the chain brake lever

A

fully forwards until it ‘clicks’ into position. If the chain brake is engaged it

should

NOT

be possible to move the saw chain using a gloved hand.

If it is possible to move the saw chain, the chain brake may be damaged. Do not use the chainsaw
until it has been inspected by a suitably qualified technician.

«
...
16
17
18
19
20
...
»

Содержание 46 cc Petrol Chainsaw



























































Отзывы:

Нет отзывов

Похожие инструкции для 46 cc Petrol Chainsaw

Бренд: EGO Страницы: 229

Бренд: Defort Страницы: 100

Бренд: Zenit Powertools Страницы: 14

Бренд: Silverline Страницы: 28

Бренд: Makita Страницы: 64

Бренд: Texas A/S Страницы: 24

Бренд: Worx Страницы: 52

Бренд: Echo Страницы: 28

Бренд: SNOWJOE Страницы: 24

Бренд: BCP Страницы: 8

Бренд: McCulloch Страницы: 3

Бренд: MacAllister Страницы: 46

Бренд: Partner Страницы: 24

Бренд: Tanaka Страницы: 16

Бренд: Tanaka Страницы: 24

Бренд: Tanaka Страницы: 52

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды