January
4,
2018
7082-150C
3
MT VERNON E2 INSERT-C
1
Important Safety Information
NOTE: Hearth & Home Technologies, manufacturer of this appli
-
ance, reserves the right to alter its products, their specifications
and/or price without notice.
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage.
For assistance or additional information, consult a qualified installer,
service agency or your dealer.
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved by
Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with
appliance).
• Do NOT Over fire - If appliance or chimney connector glows,
you are over firing.
Any such action that may cause a fire hazard.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please con-
tact your dealer for replacement glass.
Model
Mt. Vernon Insert Pellet Appliance E2
Laboratory
OMNI Test Laboratories, Inc.
Report No.
061-S-84-2
Type
Solid Fuel Room Appliance, Pellet Fuel Burn
-
ing Type
Standard
ASTM E1509-12, ULC-S628-93 and
(UM)
84-HUD, Mobile Home Approved.
FCC
Complies with Part 15 of FCC Rules. Opera
-
tion is subject to the following two conditions:
(1) this device may not cause harmful inter
-
ference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
A. Appliance Certification
NOTICE:
This installation must conform with local codes. In the
absence of local codes you must comply with the
ASTM E1509-
12, ULC S628-93, (UM) 84-HUD and ULC/ORD-C-1482.
B. BTU & Efficiency Specifications
D. Electrical Rating
115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps
E. Mobile Home Approved
•
This appliance is approved for mobile home installations when
not installed in a sleeping room and when an outside combustion
air inlet is provided.
•
The structural integrity of the mobile home floor, ceiling, and
walls must be maintained.
•
The appliance must be properly grounded to the frame of the
mobile home and use only Listed pellet vent Class “L” or “PL” con
-
nector pipe.
•
Outside Air Kit (OAK-3) must be installed in a mobile home
installation.
F. Non-Combustible Materials
Material which will not ignite and burn, composed of any combina
-
tion of the following:
-
Steel
-
Plaster
- Brick
- Iron
-
Concrete
-
Tile
-
Glass
-
Slate
Materials reported as passing
ASTM E 136, Standard Test
Method for Behavior of Metals, in a Vertical Tube Furnace of
750° C.
G. Combustible Materials
Material made of/or surfaced with any of the following materials:
- Wood
- Compressed Paper
- Plant Fibers
- Plastic
- Plywood/OSB
- Sheet Rock (drywall)
Any material that can ignite and burn: flame proofed or not, plas
-
tered or non-plastered.
The Quadra-Fire Mt. Vernon E2 Pellet Insert Appliance meets
the U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to
comply with 2020 particulate emission standards at 0.74 G/HR EPA
CFR subpart AAA, using ASTM E2779-10, ASTM 2515-11 Method-
Pellet Appliance sections, CSA B415.1-10
.
This pellet appliance
needs periodic inspection and repair for proper operation. It
is against federal regulations to operate this pellet appliance
in a manner inconsistent with the operating instructions in
the owner’s manual.
Emissions Report Number:
0061PS094E
EPA Certification #:
98-17
EPA Certified Emissions:
0.74 g/hr
*LHV Tested Efficiency:
83.2%
**HHV Tested Efficiency:
77.9%
***EPA BTU Output:
12,682 - 39,428 / HR
****BTU Input:
16,396 - 50,775 / HR
Vent Size: 3 or 4, “L” or “PL”
Hopper Capacity: 52 lbs.
Fuel Wood Pellets
* Weighted average LHV efficiency using data collected during
EPA emissions test.
**
Weighted average HHV efficiency using data collected during
EPA emissions test.
***
A range of BTU outputs based on HHV and the burn rates from
the low and high EPA tests.
****
Based on the maximum feed rate per hour multiplied by
approximately 8600 BTU’s which is the average BTU’s from a
pound of pellets.
