background image

 22 

 

 

 

 

                       7080-163D 

 

 

 

       August 3, 2018

MT. VERNON E2-C

Figure 22.1 - Fire pot with large clinker

Clinker

Figure 22.2

C.  General Maintenance and Cleaning

1.  Cleaning Fire pot using Lever

•  Frequency:

 Weekly or as needed*

•  By:

  Homeowner

*In order to maintain optimum performance, it is 

recommended that the fire pot be cleaned weekly or more 

as needed.

a.  Be sure the appliance is allowed to cool. 

b.  Open cast face of appliance

c. 

Pull fire pot floor cleaning lever two times until the ash 

falls into the ash pan below (

Figure 22.2).

d. 

It may be necessary to use your fire pot clean-out tool to 

chip away material that has built up on the sides of the 

fire pot and to push out any clinkers (

Figure 22.1).

e.  Larger clinkers may have to be removed from the top of 

the fire pot. 

f. 

If the clinker adheres to the sides of the fire pot, you will 

need  to  manually  clean  the  fire  pot.  The  fire  pot  floor 

plate must be fully closed when finished.

2.  Cleaning Ash Pan

•  Frequency:

  Weekly or every 3-5 bags

•  By:

  Homeowner

a. 

Locate the ash pan underneath the fire pot. 

b.  Slide the ash pan straight out. 

c.  Empty into a non-combustible container and re-install 

ash pan. 

d.  When replacing ash pan push it back until it catches on 

the 2 side latches. 

 

Clinkers filling the ash pan will have to be cleaned out more 

often than ash. 

Ash Disposal:

Ashes should be placed in a steel container with a tight-

fitting lid.  The container of ashes should be moved 

outdoors immediately and placed on a non-combustible 

floor or on the ground, well away from combustible 

materials, pending final disposal.  

If the ashes are disposed of by burial in soil or otherwise 

locally dispersed, they should be retained in the closed 

container until all cinders have thoroughly cooled. Other 

waste shall not be placed in this container.

3.  Ash Removal from Firebox

•  Frequency:

  Weekly or more frequently depending on 

ash build-up

•  By:

  Homeowner

a.  Be sure the appliance is allowed to cool. 

b. 

There must not be any hot ashes in the firebox during 

cleaning. 

c. 

Frequent cleaning of the ash in the firebox with a vacuum 

cleaner will help slow down the build-up of ash in the 

exhaust blower and vent system.

4.  Cleaning Heat Exchanger & Drop Tube

•  Frequency:

  Monthly or every ton of fuel (50 bags).

•  By:

  Homeowner

NOTE: 

Heavy duty vacuum cleaners may be obtained, 

specifically designed for solid fuel appliance 

cleaning. 

RISK OF FIRE

Keep combustible materials, gasoline and other 

flammable vapors and liquids clear of appliance.

WARNING

• 

Do NOT store flammable materials in the appliance’s 

vicinity.

•  Do NOT use gasoline, lantern fuel, kerosene, 

charcoal lighter fluid or similar liquids to start or 

“freshen up” a fire in this heater.

Keep all such liquids well away from the heater while it is 

in use as combustible materials may ignite.

f i r e - p a r t s . c o m

Содержание MT. VERNON E2 Series









































Отзывы: