background image

 10 

 

 

 

 

                        7039-174C 

 

 

 

 August 01, 2016

Discovery I

Recommended 

Location 

Marginal 

Location 

Location 

Not 

Recommended 

 

Recommended 

Location 

 

Location NOT 

Recommended 

Multi-level Roofs 

Windward 

Leeward 

Outside Air Kit Termination Cap

Figure 10.1

A.  Locating Your Appliance & Chimney

Location of the appliance and chimney will affect perfor-

mance.  As shown in 

Figure 10.1

 the chimney should:

  •  Install through the warm space enclosed by the build-

ing envelope. This helps to produce more draft, espe-

cially during lighting and die down of the fire.

 

•  Penetrate the highest part of the roof.  This minimizes 

the affects of wind turbulence and down drafts.

  •  Consider the appliance location in order to avoid floor 

and ceiling attic joists and rafters.

 • 

Locate termination cap away from trees, adjacent 

structures, uneven roof lines and other obstructions.

Your local dealer is the expert in your geographic area and 

can usually make suggestions or discover solutions that will 

easily correct your flue problem.

Chimney Systems

Содержание Discovery I Wood Appliance





















Отзывы: