Quadra-Fire CLASSIC BAY 1200 Скачать руководство пользователя | Manualshive

Страница: 9 / 30

background image

CB1200-I PELLET STOVE SERVICE MANUAL

CB1200-I PELLET STOVE SERVICE MANUAL

IGNITER TESTING

USING THE TEST BOX:

1) UNPLUG THE STOVE, REMOVE THE CONTROL BOX, INSTALL THE TEST BOX & PLUG IN THE STOVE.

2) TURN ON THE THERMOSTAT. (THE THERMOSTAT INDICATOR LIGHT SHOULD COME ON)

3) TURN THE IGNITER SWITCH ON.

IF THE IGNITER COMES ON--------REPLACE THE CONTROL BOX

IF THE IGNITER DOESN’T COME ON--------REPLACE THE IGNITER OR CHECK THE WIRE HARNESS

USING THE COMPONENT TEST CORD:

1) UNPLUG THE STOVE AND DISCONNECT THE IGNITER FROM THE WIRE HARNESS.

2) INSTALL THE ALLIGATOR CLIPS ONTO THE TEST CORD.

3) CLIP THE TEST CORD TO THE WIRES ON THE IGNITER AND TURN THE SWITCH ON.

TEST BOX (AS IT IS INSTALLED IN THE STOVE)

TEST CORD w/ CLIPS ATTACHED

CLIPS HOOKED UP TO THE IGNITER

IGNITER SWITCH

THERMOSTAT LIGHT

7-31-2002 PAGE 9 250-7700

«
...
7
8
9
10
11
...
»

Содержание CLASSIC BAY 1200































Отзывы:

Нет отзывов

Похожие инструкции для CLASSIC BAY 1200

Бренд: KASTOR Страницы: 57

Бренд: Nectre Fireplaces Страницы: 12

Бренд: Radijator Страницы: 86

CITY GRUNDI Maxi

Бренд: BRULA Страницы: 17

Бренд: Piazzetta Страницы: 52

Бренд: Nibe Страницы: 4

CentroPelet ZS10

Бренд: Centrometal Страницы: 12

COMBO COAL & WOOD STOVE

Бренд: New Buck Corporation Страницы: 35

SQUARE 68 - SCHEMATICS

Бренд: WANDERS Страницы: 1

Бренд: GAS ONE Страницы: 6

Ellis Cook Stove BCS01

Бренд: Boru Stoves Страницы: 32

Бренд: Hitzer Страницы: 14

Бренд: deville Страницы: 56

Бренд: Saey Страницы: 19

Бренд: Saey Страницы: 62

Бренд: IHP Страницы: 4

Бренд: Cadel Страницы: 33

Бренд: Harman Stove Company Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды