Quadra-Fire CASTILEI-CSB Скачать руководство пользователя страница 5

Страница: 5 / 32

July 7, 2015

7022-514C

CASTILE INSERT

• Installation and use of any damaged appliance.
• Modifi cation of the appliance.
• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with

unit).

• Do NOT Overfi re

Or any such action that may cause a fi re hazard.

WARNING

Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided by,
the following actions:

Reciprocating Saw

Channel Locks

Hammer

Phillips

Screwdriver

Tape Measure

Plumb Line

1/4” Self-Tapping Screws

Framing Material

Hi-temp Caulking Material

Gloves

Safety Glasses

Framing Square

Electric Drill & Bits (1/4”)

Level

May also need:
Vent Support Straps

Venting Paint

Tools and building supplies normally required
for installation, unless installing into an existing
masonry fi replace:

C. Tools And Supplies Needed

B. Thermostat Wall Control Location

The thermostat wall control’s location will have some affect
on the appliance’s operation.

• Maximum wire length from appliance is 100 feet (30.48m)

continuous unspliced wire. Recommended 20 gauge wire,
solid copper

•

When located close to the appliance, it may require a

slightly higher temperature setting to keep the rest of the
house comfortable.

•

When located in an adjacent room or on a different fl oor

level, you will notice higher temperatures near the appli-
ance.

D. Inspect Appliance and Components

•

Open the appliance and remove all the parts and articles
packed inside the Component Pack. Inspect all the parts
and glass for shipping damage.

• Report to your dealer any parts damaged in shipment.

•

All labels have been removed from the glass door.

• Plated surfaces have been wiped clean with a soft cloth,

if applicable.

•

Read all the instructions before starting the installation.
Follow these instructions carefully during the
installation to ensure maximum safety and benefi t.

•

Follow pipe manufacturer instructions for installation
and air clearance requirements.

WARNING

Fire Risk.

Damaged parts could impair safe operation. Do NOT
install damaged, incomplete or substitute compo-
nents.

Содержание CASTILEI-CSB

































Результаты поиска

Содержание CASTILEI-CSB

Отзывы:

Похожие инструкции для CASTILEI-CSB

Бренды по названию

Популярные бренды

Quadra-Fire CASTILEI-CSB, Руководство по установке

Результаты поиска

Содержание CASTILEI-CSB

Отзывы:

Похожие инструкции для CASTILEI-CSB

Бренды по названию

Популярные бренды