Quadra-Fire CASTILEI-CSB Скачать руководство пользователя страница 20

Страница: 20 / 32

7022-514C

July 7, 2015

CASTILE INSERT

C. Door Handle Removal

Tools Required:

5/32 Allen wrench

1. Open the door. Using a 5/32 Allen wrench, loosen set

screw by a couple of turns, but do not remove.

2. Push the pin completely out and remove the handle.

3. Re-install in reverse order.

D. Door Removal

1. Remove the door handle and face. Follow instructions

from D above.

2. The door can now be lifted off the hinges.

3. Re-install in reverse order.

E. Adjustable Hearth Support

Size: 9”d x 45”w, 2” to 10” Height Adjustment

Included in Kit:

(1) trim top, (1) trim front, (2) trim sides,

double-sided tape (already installed)

Tools Needed:

Phillips head screwdriver, sheet metal

shears, measuring tape, gloves

1. The 10 screws on each set of scissors will already be

loose when shipped.

Figure 20.1.

2. Expand scissors to desired height. Tighten screws to

hold in place using Phillips head screwdriver.

3. Measure front and side trims to required height to cover

scissors and mark pieces for cutting. Cut excess material
from

top

of trims edge, not bottom. This edge will be

sharp; wear gloves to prevent injury to your hands. The
cut edge fi ts under lip of top trim, so it allows for some
variance in your straight edge.

Figure 20.2.

4. The double-sided tape that holds front and side trims to

scissors has a powerful bonding adhesive. Adjustments
are extremely diffi cult once trim has adhered to tape. Do
a dry run fi rst without removing paper from tape.

5. Place cut edge of trim under top lip and into position on

scissors. Place side pieces on fi rst and then front piece.
The front piece overlaps side pieces.

6. Once you are satisfi ed with the positioning, remove trim

and set aside.

7. Remove the paper from double-sided tape that is to

accept trim side. Align side and then press hard against
tape to secure side piece. Repeat for other side. Install
front trim piece last.

8. There are 3 holes in the back fl ange of the top to secure it

to the wall if necessary. Use the appropriate fastener for
the type of wall material, i.e., brick, sheetrock, etc.

NOTE

: 3/8 inch (9.5mm) thick tile or like material can be

cut to size and fi t under lip of top trim edge for a decora-
tive touch.

Figure 20.3.

Figure 20.1

Figure 20.2

Figure 20.3

DOUBLE-SIDED TAPE

SCREWS ARE CIRCLED

EXPLODED VIEW OF SCISSORS

Decorative tile

may be installed

INSTALL FRONT TRIM LAST.

CORNERS OVERLAP SIDE

TRIM PIECES

EXPAND SCISSORS TO DESIRED HEIGHT

CUT TOP EDGE OF TRIM,

NOT BOTTOM EDGE

WARNING

Sheet metal trim edges will be sharp.
For safety purposes wear gloves.

Injury can occur.

Содержание CASTILEI-CSB

































Результаты поиска

Содержание CASTILEI-CSB

Отзывы:

Похожие инструкции для CASTILEI-CSB

Бренды по названию

Популярные бренды

Quadra-Fire CASTILEI-CSB, Руководство по установке

Результаты поиска

Содержание CASTILEI-CSB

Отзывы:

Похожие инструкции для CASTILEI-CSB

Бренды по названию

Популярные бренды