background image

15

April 23, 2019

7021-801B

CASTILE FREESTANDING

C. Negative Pressure

NOTE

: The appliance exhaust outlet is designed to 

accommodate 3 inch venting. Use of 4 inch 

venting requires the use of a 3-to-4 inch exhaust 

vent increaser in addition to any other venting 

components needed, sold separately.

Negative pressure results from the imbalance of air 

available for the appliance to operate properly. It can be 

strongest in lower levels of the house.

Causes include:

• 

Exhaust fans (kitchen, bath, etc.)

•  Range hoods

•  Combustion air requirements for furnaces, water 

appliances and other combustion appliances

•  Clothes dryers

• 

Location of return-air vents to furnace or air 

conditioning

•  Imbalances of the HVAC air handling system

•  Upper level air leaks such as: 

 

-

Recessed lighting

 

-

Attic hatch

 

-

Duct leaks

To minimize the effects of negative air pressure:

•  Install the outside air kit with the intake facing prevailing 

winds during the heating season

•  Ensure adequate outdoor air for all combustion 

appliances and exhaust equipment

•  Ensure furnace and air conditioning return vents are 

not located in the immediate vicinity of the appliance

•  Avoid installing the appliance near doors, walkways or 

small isolated spaces

• 

Recessed lighting should be a “sealed can” design

•  Attic hatches weather stripped or sealed

•  Attic mounted duct work and air handler joints and 

seams taped or sealed

E. Chimney and Exhaust Connection 

1.  Chimney & Connector:

 Use 3 or 4 inch (76-102mm) 

diameter type “L” or “PL” venting system. It can be 

vented vertically or horizontally.

D. Draft

Draft is the pressure difference needed to vent an 

appliance successfully. When an appliance is drafting 

successfully, all combustion byproducts are exiting the 

home through the chimney.

Install through the warm airspace enclosed by the building 

envelope. This helps to produce more draft, especially 

during lighting and die-down of the fire.

Considerations for successful draft include:

• 

Preventing negative pressure

• 

Location of appliance and chimney

NOTE: 

All pipe must be welded seam pipe whenever 

possible. Seal pipe joints with high temperature 

silicone (500°F [260°C] minimum rated only).

WARNING

USE ONLY RECOMMENDED VENTING 

COMPONENTS; OTHERWISE MAKESHIFT PARTS MAY 

RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, 

OR DEATH. 

NOTICE:

 Hearth & Home Technologies assumes no 

responsibility for the improper performance of 

the chimney system caused by:

•  Inadequate draft due to environmental conditions

•  Down drafts

•  Tight sealing construction of the structure

•  Mechanical exhausting devices

2.  Mobile Home:

 Approved for all Listed pellet vent. If 

using the 3 inch (76mm) vertical Top Vent Adapter Kit 

or the 3 to 6 inch (76-152mm) Top Vent Offset Adapter, 

use Listed double wall flue connector. A Quadra-Fire 

Outside Air Kit must be used with manufactured home 

installations.

3.  Residential:

 The 3 inch (76mm) vertical Top Vent 

Adapter Kit and the 3 to 6 inch (76 to 152mm) Top Vent 

Offset Adapter are tested to use 24 gauge single wall 

flue connector or Listed double wall flue connector to 

Class A Listed metal chimneys, or masonry chimneys 

meeting International Residential Code standards for 

solid fuel appliances.

4. 

Install vent at clearances specified by the vent 

manufacturer.

5. 

Secure exhaust venting system to the appliance with 

at least 3 screws. Also secure all connector pipe joints 

with at least 3 screws through each joint.

6.  DO NOT INSTALL A FLUE DAMPER IN THE 

EXHAUST VENTING SYSTEM OF THIS Appliance.

7. 

DO NOT CONNECT THIS Appliance TO A CHIMNEY 

FLUE SERVING ANOTHER APPLIANCE.

WARNING

Risk of Asphyxiation!

 

Negative pressure can cause spillage of combustion 

fumes and soot.

Содержание CASTILE-MBK-C





























Отзывы: