Quadlogic MiniCloset-5c Скачать руководство пользователя страница 86

Страница: 86 / 117

Appendix

Quadlogic Controls Corporation



Make sure the RS-485 wires are spliced together correctly.



Like colors from pigtails connect to the same circuit.



Make sure enough insulation is stripped off wire to make solid contact with the
circuit.



Use wire nuts that are rated for the number of wires and gauge.



Avoid excess bare wire outside of the wire nut.



Make sure that the wires are not shorted together or to the box.



Make sure there are no “T” branches in the RS-485 network.



Pigtails make a short wire connection to straight network.



Make sure there are no bare wires touching any metal conductors.



Make sure data link is not more than 4000 feet with the meter at the end of the link.



Make sure terminating resistors are in place.



Make sure that there is only ONE communications module with a modem in the data
link."

If the problems persists after verification contact a Quadlogic technical support representative for
further assistance. It is possible that the Quadlogic device is defective and may need
replacement.

Содержание MiniCloset-5c
























































































Результаты поиска

Содержание MiniCloset-5c

Отзывы:

Похожие инструкции для MiniCloset-5c

Бренды по названию

Популярные бренды

Quadlogic MiniCloset-5c, Руководство по установке

Результаты поиска

Содержание MiniCloset-5c

Отзывы:

Похожие инструкции для MiniCloset-5c

Бренды по названию

Популярные бренды