background image

USER MANUAL

 

 
LASER EXPOSURE WARNING      
 

LASER LIGHT 

AVOID DIRECT EYE EXPOSURE 

 

Further guidelines and safety programs for safe use of lasers can be found in the 

ANSI Z136.1 Standard “For Safe Use of Lasers”, available from 

“www.laserinstitute.org”.  Many local governments, corporations, agencies, 

military and others, require all lasers to be used under the guidelines of ANSI 

Z136.1. Laser Display guidance can be obtained via the International Laser 

Display Association, www.laserist.org.    

 

LASER EMISSION DATA      

* As measured under IEC measurement conditions for classification. 

 

LASER COMPLIANCE STATEMENT      

According to the EN 60825-1

1994 + A1

2002+A2:2001 + COTT regulations, this 

laser fall under the classification 3B.Direct eye exposure can be dangerous. 

 
 
 
 
 
 
 

Laser Classification 

Class 3B   

Green Laser Medium 

DPSS Nd:YVO4, 532nm 

Red Laser Medium 

LD GaAlAs 650nm, typical     

Beam Diameter 

<5mm at aperture 

Pulse Data 

All pulses < 4Hz (>0.25sec) 

Divergence (each beam) 

<2mrad 

Divergence (total light) 

<160 degrees 

Laser Power   

Red>80mW, Green>30mW 

Содержание 152.740

















Отзывы: