background image

 

  Q23 Expansion Module 

Page 29 

CONNECTIONS 

This section describes the function and connections to the various connectors on the Q23 Module. 

Power Supply 

The  Q23  Module  is  designed  to  operate  with  DC  power  supply  voltages  of  nominally  12  or  24  volt.    The  Q23 
Module  will  operate  on  any  DC  power  supply  voltage  within  the  range  11  to  28  volts.    The  Q23  Module  draws 
approximately 80mA at 12 volts and 60mA at 24.0 volts power supply input voltages. 

The power connector is located on the lower panel of the Q23 Module and is labelled 

‘PWR’

.  The terminals of the 

power connector are: 

G

 

Ground, negative lead of supply. 

+

 

Positive lead of supply 

C

 

Optional remote power control line. 

Note 

The 

‘+’ switched positive output is also present on the ‘+’ connectors of the ‘ANALOG I/O’‘DIGTAL OUT’ 

and   

‘AUX  OUT’  connectors.    This  ensures  that  attached  peripheral  devices  also  power  down  during 

remote power control shut down and therefore do not ‘back feed’ power to the Q23 Module. 

The DC power supply to the Q23 Module must be adequately smoothed and free from noise and voltage transients.  
Where the DC supply is derived from the AC mains, or batteries with an associated AC mains battery charger these 
devices must comply with the relevant electrical regulations. 

The optional remote power control line is used to remotely power up and power down the Q23 Module.  This line is 
usually connected to the switched positive power output line of an associated Q22 

– DATRAN II eXcel Module. 

With  power  applied  to  the  module,  applying  a  voltage  in  excess  of  10  volts  to  the  remote  power  control  line  will 
power up the Q23 Module. 

Note 

Refer the Technical Notes section for more details on the remote power control function. 

Digital Inputs 

The Q23 Module has 8 digital input channels.  These are available at a 9 way connector  labelled 

‘DIGITAL IN’

 on 

the front panel of the Q23 Module.  The digital input channels are numbered 1 to 8.  The terminal 

‘G’

 is a system 

ground connection. 

  A  digital  input  channel  is  in  the  ON  state  when  the  corresponding  input  terminal  on  the  digital  inputs 

connector is grounded, i.e. connected to the 

‘G’

 terminal on the digital inputs connector. 

  A  digital  input  channel  is  in  the  OFF  state  when  the  corresponding  input  terminal  on  the  digital  inputs 

connector is open circuit or at the supply voltage potential. 

Note 

The input voltage to any digital input should not be allowed to go above the module’s power supply voltage. 

The  digital  input  can  be  switched  with  a  variety  of  devices.    These  can  include  mechanical  switches,  solid-state 
switches, transistors, transducers, etc. 

Digital Outputs 

The Q23 Module has 8 digital output channels: 

  Digital output channels 1 to 4 are available at a 6 way connector labelled 

‘DIGITAL OUT’

 on the front panel 

of  the  Q23  Module.    The  digital  output  channels  are  numbered  1  to  4.    The  terminals  labelled 

‘+’

  are 

connected to the switched positive rail 

of the module’s power supply. 

  Digital output channels 5 to 8 are available at a 6 way connector  labelled 

‘AUX OUT’

 on the bottom panel 

of  the  Q23  Module.    The  digital  output  channels  are  numbered  5  to  8.    The  terminals  labelled 

‘+’

  are 

connected to the swi

tched positive rail of the module’s power supply. 

In  the  ON  state  a  digital  output  channel  is  shorted  to  ground.    In  the  OFF  state  a  digital  output  channel  is  open 
circuited.    The  digital  output  channels  are  capable  of  switching  1  amp  at  up  to  26.5  volts.    The  output  voltage  is 
clamped  at  65  volts  during  inductive  switching  eliminating  the  need  for  reversed  biased  diodes  across  inductive 
loads. 

Содержание Q23



















































Отзывы: