QSI 600 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 61

background image

44

Installing the 8-position colour filter wheel

Always remove the colour filter wheel when installing or removing filters. To change filters or

replace the colour filter wheel the front cover of the camera must be removed. Place the camera

face up on a stable surface. Using the included Allen wrench, carefully remove the screws

holding the camera cover to the camera body. Note that 2 or 4 of the screws holding the 8-

position cover to the body are longer than the rest. The longer screws go through the 8-position

CFW Adapter Plate and screw directly into the QSI 600 Series body, shown with blue arrows

below. Lift the cover straight up to expose the colour filter wheel.

Remove the colour filter wheel by unscrewing the screw in the centre of the filter wheel.

Carefully lift out the colour filter wheel. To replace the colour filter wheel a slight pressure must

be applied with the outside O-ring against the capstan motor that drives the colour filter wheel.

Carefully line up the centre screw for the 8-position CFW (shown above) and press the filter

wheel O-ring gently against the capstan motor. Lining up a filter or empty filter position over the

shutter opening can help to achieve the proper alignment.

Screw in the centre screw until it is quite snug. 5 inch-pounds or more of force if you have a

torque wrench. Stainless steel screws naturally "lock" with anodized aluminium. The screw is

tight enough when you can hear the screw "break free" when it is loosened.

«
...
42
43
44
45
46
...
»

Содержание 600 Series






























































Отзывы:

Нет отзывов

Похожие инструкции для 600 Series

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 32

HomeHawk KX-HNC800

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 100

BL-C10A - Network Camera - Pan

Бренд: Panasonic Страницы: 4

Бренд: Wansview Страницы: 28

Split Vision VSLR3

Бренд: Federal Signal Corporation Страницы: 4

Бренд: Edimax Страницы: 137

Бренд: GE Security Страницы: 26

Бренд: Patlite Страницы: 2

Бренд: evology Страницы: 12

EXPCMR-ALG-1080P-12V

Бренд: Larson Electronics Страницы: 4

Бренд: Avtech Страницы: 44

Бренд: Elpas Страницы: 3

Бренд: Lilin Страницы: 111

CN-Magnetic-Mini

Бренд: C.Nord Страницы: 2

Бренд: Clover Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды