QSI 600 Series Скачать руководство пользователя страница 14

Страница: 14 / 61

Note:

Power up initialisation can take up to 6 seconds. It is not possible to connect to the camera

from an image application during this time. Any attempt to do so will cause an error message to be

displayed by your imaging application.

Note:

The camera is designed to operate on stable, regulated 12 V DC power and Consumes less

than 2 amps at full power. Dc power inputs above or below 12V will decrease the maximum cooling

capability of the camera by increasing power dissipation or lowering cooling efficiency. If the input

voltage is below 11V or above 14V the camera will report and error until the voltage is returned to

the specified range. See Status and Notification below.

Caution:

Applying an input voltage over 16V or under 10V may permanently damage your camera

and will void the camera warranty

Note:

The camera power connector uses a standard 2.1 mm coaxial DC power connector with

centre positive connector. The outside diameter is 5.5 mm and the length is 10 mm.

Caution:

Because of the wide range of potential power sources (especially with field operations

that can employ batteries, generators, DC inverters etc.) there is a real possibility of damaging your

camera and other equipment by creating unexpected ground loops and different ground reference

potentials between your equipment.

It is highly recommended that the included AC adaptor be used to power the camera at all times, if

a power source other than the included is used it is your responsibility to insure it is suitable. Avoid

sharing the camera DC power source with other devices that can produce excessive noise (old

technology dew heaters, etc.) and possible ground loops that could interfere with the reliable

operation, or even damage your equipment.

If you choose to use a power source other than the included AC adapter and are uncertain about

meeting these requirements, please

USB connector

The cameras USB interface is compatible with USB 2.0 and 1.1. The inclu ded USB 2.0 cable

plugs into the USB port on the camera connector panel. The other side connects to any

standard USB port on your computer. All camera control commands and resulting images are

passed over the USB cable.

Содержание 600 Series






























































Результаты поиска

Содержание 600 Series

Отзывы:

Похожие инструкции для 600 Series

Бренды по названию

Популярные бренды

QSI 600 Series, Руководство пользователя

Результаты поиска

Содержание 600 Series

Отзывы:

Похожие инструкции для 600 Series

Бренды по названию

Популярные бренды