QRP Labs QCX-mini CW Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 121

QRP Labs QCX-mini CW Скачать руководство пользователя страница 20

There are two PCB panels supplied in the kit, each is packaged in a separate static-proof
zip-lock bag. The main PCB has SMD components soldered to both sides; handle it with
care to avoid dislodging any components. The display PCB also has several SMD
components installed.

The display PCB panel has cut-out areas, which are used to create additional PCBs used in
the design. These additional PCBs will be broken off the display PCB along lines of drill-
holes.

The “Controls PCB” connects to the main PCB using a 2x4-pin header connector, and is
fixed with a hex spacer and screws. This board holds the gain control and rotary encoder,
as well as the two push-button switches.

The controls PCB needs to be slightly higher relative to the main board than the display
PCB, this is accomplished using two small spacer PCBs, one which fits on the 2x4-pin
header, and one which fits on the hex spacer; together these elevate the controls PCB by
1.6mm (one standard FR4 PCB thickness) above the height of the display PCB.

The uSDX PCB is a small daughtercard that can be installed on the main PCB and provides
an easy conversion of the QCX-mini to the uSDX SSB SDR transceiver. Components are
not supplied to populate this PCB. The conversion is supported by the uSDX group

https://groups.io/g/ucx

and there is no technical support from QRP Labs. The daughtercard

is supplied as-is, to assist this conversion for experimenters who wish to try uSDX.

QCX-mini assembly Rev 1.05

20

«
...
18
19
20
21
22
...
»

Содержание QCX-mini CW


























































































































Отзывы:

Нет отзывов