QRP Labs QCX-mini CW Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 121

QRP Labs QCX-mini CW Скачать руководство пользователя страница 106

reverse polarity by D33, a Schottky diode type 1N5819. This also drops the voltage by 0.3
to 0.4V, which has the effect of reducing the output power. D33 is shown on the
microcontroller section of the circuit diagram, see earlier.

If you are brave, and confident that you will NEVER connect power to the radio with
reversed polarity, you can omit this diode and fit a jumper wire over it.

5. Fault-finding

Refer to

http://qrp-labs.com/qcx/qcxtrouble

and the groups.io discussion group for more tips!

5.1

Blank LCD or blocked LCD

If your LCD screen looks like either of these, then it is a sure sign that you have not
adjusted the contrast trimmer potentiometer R47.

5.2

No back-light at all

If there is no LCD back-light at all, check you have properly installed the LCD connector
between the main PCB and the LCD board.

No back-light can also be NORMAL! If the backlight setting in the “Other” menu
configuration (in menu 7) is set to OFF, then the backlight will be off, naturally. The QCX-
mini screen is readable without the backlight so it will be no problem to change this menu
entry.

5.3

A row of blocks appears on the top row

If you see a row of blocks along the top of the LCD module, and the bottom row is empty,
this means that the microcontroller has not communicated with the LCD module.

Check that your IC2 microcontroller is correctly installed in its 28-pin socket, with the correct
orientation (dimple on the chip matches the dimple on the socket and the PCB silkscreen).
Check that all of the pins of IC2 are correctly inserted in the socket,
not bent.

5.4

DC voltage readings

The following table lists the DC voltage read at various points around
the circuit. This may aid troubleshooting. The voltage measurements

QCX-mini assembly Rev 1.05

106

«
...
104
105
106
107
108
...
»

Содержание QCX-mini CW


























































































































Отзывы:

Нет отзывов