QHT Direct Vent DVF-4 Rigid Скачать руководство пользователя

Страница: 3 / 24

IMPORTANT INFORMATION

Please read this page carefully.

ALL BOILERS MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL

PLUMBING, HEATING AND ELECTRICAL CODES AND ORDINANCES, AS WELL AS THE

REGULATIONS OF THE SERVING ELECTRICAL, WATER AND GAS UTILITIES.

All systems should be designed by competent licensed heating contractors, and only

persons knowledgeable in the layout and installation of heating systems should attempt

the installation of the B10 boiler. It is the responsibility of the installing contractor to see

that all controls are correctly installed and operating properly when the installation is

completed.

Do not burn volatile garbage, gasoline, naphtha or other flammable liquids other than

No. 2 fuel oil. All flammable liquids (especially gasoline), chemicals, rags, paper, wood

scraps, debris, etc., should be kept away from the boiler at all times. Keep the boiler area

clean and free of all fire hazards.

Please read the literature and warranties supplied by the manufacturers of the various

accessory equipment. This equipment is warranted by the respective manufacturers,

not by Quincy Hydronic Technology, Inc. Each piece of equipment must be installed and

used according to the recommendations of the manufacturer.

Codes and Regulations:

Installation of the boiler, burner, oil tank and related equipment must conform to

national, state and local regulating agencies and codes applicable to the instal-

lation of the equipment. In the absence of local requirements, the following codes

apply:

A. NFPA

- #31 Installation of Oil Burning Equipment

B. NFPA

- #70 National Electric Code

C. NFPA

- #211 Chimneys and Vents

D. ANSI

- #Z223.1 National Fuel Gas Code

E. ANSI

- Domestic Gas Conversion Burner

F. CAN/CGA - B149 Installation Codes

G. ANSI

- CSD-1

H. CSA

-C22.1 Canadian Electrical Code, Part1

The above codes are available from:

National Fire Protection Association (NFPA)

Battery March Park

Quincy, MA 02269

http://www.nfpa.org

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44134

http://www.csa-international.org

Содержание Direct Vent DVF-4 Rigid

























Результаты поиска

Содержание Direct Vent DVF-4 Rigid

Отзывы:

Похожие инструкции для Direct Vent DVF-4 Rigid

Бренды по названию

Популярные бренды

QHT Direct Vent DVF-4 Rigid, Руководство по установке

Результаты поиска

Содержание Direct Vent DVF-4 Rigid

Отзывы:

Похожие инструкции для Direct Vent DVF-4 Rigid

Бренды по названию

Популярные бренды