Qasair 1200HL-2, Руководство по установке

Страница: 19 / 62

QASAIR Installation Instructions
17
Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations. Connection to be carried
out by a registered electrician.
Flue fitting instructions 3 Flare models only
1.
Check that the flue is the correct length prior to fitting.
2.
Peel back PVC on the flue.
3.
Place the rangehood on a level surface.
4.
Remove the phillips head transit screws from the top of the rangehood.
5.
Position the flue over the outlet and place all the rivets in the holes available and then fasten them.
6.
Fit the flue back plate.
installation instructions
1.
Prepare wall by marking level line at desired height above cooktop.
2.
Plumb line from centre of cooktop to ceiling and mark flue cut out. Position mounting bracket on wall
and fix with four screws. Mounting bracket is not necessary when installing over a splashback.
Note: The fixing bracket is 32mm shorter than the rangehood and should be located from the centre
only.
3.
Cut a neat hole through the ceiling and remove any obstructing timbers.
Note: Various offsets are available from your QASAIR dealer to duct around any major structural
beams which cannot be removed. Ask your QASAIR dealer for advice.
4.
In the case of back ducted models, cut a hole in the wall at the desired height.
5.
Locate solid fixing point in wall to support hood. If there is no solid fixing point it will have to be
placed in the wall before proceeding. QASAIR recommend at least four (4) fixing points.
6.
Drill holes in back of unit at suitable fixing points.
7.
Drill 20mm hole in the rear of unit for 240 volt power cable as close as possible to junction box or
use hole below the junction box.
8.
Place flue over spigot of hood then carefully lift into position on level line. Ensure flue is pushed into
position and electrical cable is fed into rear of unit.
9.
Duct in approved manner to outside atmosphere.
cleaning of stainless steel
QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.
This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes stainless
by the chromium oxidising in the open air to form a protective coating of chromium oxide. This coating
can be upset by coming in contact with a substance that will attack the chromium oxide, such as a
lemon solution or any cleaner with a preservative in it.
Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or warm
soapy water with soap will do it. Do not use powder detergent.
instructions
f o r models
3F 900L-2
3F 1200L-2
3F1200L-3
3F 1500L-3
SF 900L-1
SF 900L-2
SF 1200L-2
ST 900L-1
ST 900L-2
ST 1200L-2
MAJ 900L-1
MAJ 900L-2
MAJ 1000L-2
MAJ 1200L-2
MAJ 1500L-2
IN 600L-1
IN 900L-2
IN 1200L-2
IN 1200L-3
STA 900L-2
STAR 900L-2
STA 1200L-2
STAR 1200L-2
SMF 600L-1
SMF 900L-1
SMF 900L-2
SMF 1000L-2
SMF 1200L-2
SMF 1500L-2
SMF 1500L-3
SMF 1800L-3
FAS 900L-2
FAS 1200L-2