QA1 MUK12 Скачать руководство пользователя страница 1

9919-211 

 

Rev. 06082017 

 

 

Technical Support Line: (952) 985-5675   Email: [email protected] 

 

21730 Hanover Ave. 
Lakeville, MN 55044 

www.QA1.net 

 

INSTALLATION INSTRUCTIONS 

MUSTANG K-MEMBER 

P/N MUK11, MUK12, MUK13 

 

 

 
 
 
READ ALL INSTRUCTIONS CAREFULLY AND THOROUGHLY PRIOR TO STARTING INSTALLATION. PRODUCTS THAT HAVE BEEN INSTALLED ARE NOT ELIGIBLE FOR 
RETURN. USE THE PROPER JACKING LOCATIONS. DEATH OR SERIOUS INJURY CAN RESULT IF INSTRUCTIONS ARE NOT CORRECTLY FOLLOWED. A GOOD 
CHASSIS MANUAL, AVAILABLE AT YOUR LOCAL PARTS STORE, MAY ALSO AID IN YOUR INSTALLATION.

 

 

                                                                                                           • 

DISCLAIMER / WARRANTY 

• 

 

QA1  WARRANTS  THAT  THE  PRODUCTS  WILL  BE  FREE  FROM  DEFECTS  IN  MATERIAL  AND  WORKMANSHIP  FOR  ONE  YEAR  FROM  DATE  OF  SALE  TO  THE 
ORIGINAL  PURCHASER.  QA1  MAKES  NO  OTHER  WARRANTY  OF  ANY  KIND,  EXPRESSED  OR  IMPLIED.  QA1  SHALL  HAVE  NO  OBLIGATION  UNDER  THE 
FOREGOING  WARRANTY  WHERE  THE  DEFECT  IS  THE  RESULT  OF  IMPROPER  OR  ABNORMAL  USE,  YOUR  NEGLIGENCE,  VEHICLE  ACCIDENT,  IMPROPER  OR 
INCORRECT INSTALLATION OR MAINTENANCE, NOR WHEN THE PRODUCT HAS BEEN REPAIRED  OR ALTERED IN ANY WAY. QA1’S LIABILITY IN THE CASE OF 
DEFECTIVE PRODUCTS SUBJECT TO THE FOREGOING WARRANTY SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT, AT QA1’S OPTION, OF THE DEFECTIVE 
PRODUCTS. 
 
THE USER UNDERSTANDS AND RECOGNIZES THAT RACING PARTS, SPECIALIZED STREET ROD EQUIPMENT, AND ALL PARTS AND SERVICES SOLD BY QA1 ARE 
EXPOSED TO MANY AND VARIED CONDITIONS DUE TO THE MANNER IN WHICH THEY ARE INSTALLED AND USED. QA1 SHALL BEAR NO LIABILITY FOR ANY 
LOSS, DAMAGE OR INJURY, EITHER TO A PERSON OR TO PROPERTY, RESULTING FROM THE INSTALLATION, DIRECT OR INDIRECT USE OF ANY QA1 PRODUCTS 
OR INABILITY BY THE BUYER TO DETERMINE PROPER USE OR APPLICATION OF QA1 PRODUCTS. WITH THE EXCEPTION OF THE LIMITED LIABILITY WARRANTY 
SET FORTH ABOVE, QA1 SHALL NOT BE LIABLE FOR ANY CLAIMS, DEMANDS, INJURIES, DAMAGES, ACTIONS, OR CAUSES OF ACTION WHATSOEVER TO BUYER 
ARISING OUT OF OR CONNECTED WITH THE USE OF ANY QA1 PRODUCTS. MOTORSPORTS ARE DANGEROUS; AS SUCH, NO WARRANTY OR REPRESENTATION 
IS MADE AS TO THE PRODUCT’S ABILITY TO PROTECT THE USER FROM INJURY OR DEATH. THE USER ASSUMES THAT RISK! 

 

TOOLS AND SUPPLIES REQUIRED 

 

                        • Floor Jack                            • Jack Stands  

    •Spring Compressor                        

                        •Wrench Set                          • Socket Set                  •Engine Hoist          •Tape Measure 

 

PRE-INSTALLATION NOTES                    ENGINE 

 

                MUK11 for 79-93 cars             5.0L WINDSOR 

     MUK12 for 96-04 cars             4.6L MODULAR 
     MUK13 for 94-95 cars             5.0L WINDSOR 

 

1.

 

QA1 does not recommend driving the vehicle until it has been properly aligned due to changes in suspension 
geometry that will affect the handling characteristics of the vehicle. 

A front end alignment should be performed by 

a qualified alignment shop after any changes to the suspension system.

 

 

 

 
 
 
 
 

NOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. 

K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS. 

Содержание MUK12







Отзывы: