background image

4

5

INSTALLATION AND OPERATION MANUAL SOLAR MODULES – Q.PRO L-G4.1, Q.PRO L-G4.2, Q.PLUS L-G4.1, Q.PLUS L-G4.2 – NA

INSTALLATION AND OPERATION MANUAL SOLAR MODULES – Q.PRO L-G4.1, Q.PRO L-G4.2, Q.PLUS L-G4.1, Q.PLUS L-G4.2 – NA

Validity

These instructions are only valid for crystalline solar modules 
from the company Hanwha Q CELLS. Hanwha Q CELLS assumes 
no liability for damage resulting from failure to observe these 
instructions. 

 

Ä

Please observe the wiring and dimensioning of the system.

 

Ä

The installer of the system is responsible for compliance with all 
necessary safety regulations during set-up and installation.

Hanwha Q CELLS assumes no liability on the basis of these 
instructions. Hanwha Q CELLS is only liable in the context of 
contractual agreements or in the context of accepted guarantees. 
Hanwha Q 

CELLS accepts no other responsibility for the 

functionality and safety of the modules. 

 

Ä

Please observe the instructions for any other system components 
that may be part of the complete solar power system. It may be 
necessary to carry out a structural analysis for the entire project. 

 

Ä

If your questions are not satisfactorily answered in the 
manual, please contact your system supplier. 

• 

The information contained within this document is subject to 
change without notice.

Additional information can be found on our website at 
www.q-cells.com.

Information for the Operator

 

Ä

Please keep this manual for the entire life of the solar power 
system.

 

Ä

Please contact your system supplier for information concerning 
the formal requirements for solar power systems.

 

Ä

Please be sure to contact the relevant local authorities and energy 
providers regarding regulations and permit requirements prior 

to installation of the solar power system. Your financial success 
depends on the fulfillment of these requirements. 

Other applicable documents

This installation manual is only valid in combination with the 
following technical information.

DOCUMENT TYPE

Product data sheet

Packaging and transport information

1 INTRODUCTION

2.1  Technical specifications

2 PLANNING

Fig. 1: 

 External dimensions (inch and mm) and components for Q.PRO L-G4.1, 

Q.PRO L-G4.2, Q.PLUS L-G4.1, Q.PLUS L-G4.2

C-SI MODULES (L) FOR DATA SHEETS

≥ 

47.24'' (

≥ 

1200 mm)

39.4''

(1000 mm)

51.5'' (1308 mm)

78.5'' (1994 mm)

1.38" (35 mm)

Junction bo×

4 × Mounting slots (DETAIL A)

8 × Drainage holes 0.12 × 0.24" (3 × 6 mm)  

Cable with

connectors

Frame

6 × Grounding holes, Ø 0.18'' (4.5 mm)

DETAIL A

0.63" (16 mm)

0.33" (8.5 mm)

1.0" (25.5 mm)

37.4''

(949 mm)

4 × Drainage holes 0.47 × 0.47" (11.9 × 11.9 mm)

DETAIL B

0.39" (10 mm)

0.28" (7 mm)

0.98" (25 mm)

4 × Mounting slots system Tracker (DETAIL B)

37.4''

(950 mm)

15.7'' (400 mm)

5.91''

(150 mm)

NA

Additional information can be found in the currently valid data sheets available at www.q-cells.com.

PRODUCT LINE

Q.PRO L-G4.1

Q.PLUS L-G4.1

Q.PRO L-G4.2

Q.PLUS L-G4.2

Type

Polycrystalline

Q.ANTUM

Polycrystalline

Q.ANTUM

Length [in]

78.5 (1994 mm)

78.5 (1994 mm)

78.5 (1994 mm)

78.5 (1994 mm)

Width [in]

39.4 (1000 mm)

39.4 (1000 mm)

39.4 (1000 mm)

39.4 (1000 mm)

Frame height [in]

1.38 (35 mm)

1.38 (35 mm)

1.38 (35 mm)

1.38 (35 mm)

Weight [lb]

52.9 (24 kg)

52.9 (24 kg)

52.9 (24 kg)

52.9 (24 kg)

Max. system voltage V

SYS

 

[V]

1500 (IEC) / 1000 (UL)

1500 (IEC) / 1000 (UL)

1500 (IEC) / 1500 (UL)

1500 (IEC) / 1500 (UL)

Max. fuse rating [A]

15

15

15

15

Permissible temperature 

range [°F (°C)]

–40 to +185 (–40 to +85)

Junction box protection 

class

 IP67 with bypass 

diodes

 IP67 with bypass 

diodes

 IP67 with bypass 

diodes

 IP67 with bypass 

diodes

Connector protection class

IP68

IP68

IP68

IP68

Fire protection class

C / Type 1

C / Type 1

C / Type 1

C / Type 1

Wind / Snow load

[lbs/ft

2

]

50 (2400 Pa) /  
112 (5400 Pa)

50 (2400 Pa) /  
112 (5400 Pa)

50 (2400 Pa) /  
112 (5400 Pa)

50 (2400 Pa) /  
112 (5400 Pa)

Max. Load (UL) [lbs/ft²]

75 (3600 Pa)

75 (3600 Pa)

75 (3600 Pa)

75 (3600 Pa)

Load Rating (UL) [lbs/ft²]

33 (1600 Pa)

33 (1600 Pa)

33 (1600 Pa)

33 (1600 Pa)

Certificates

CE-compliant; IEC 61215 (Ed.2) see page 8; IEC 61730 (Ed.1) Application Class A;  
UL 1703

1

   Test-load in accordance with IEC 61215

Содержание Q.PLUS L-G4.1













Отзывы: