Python 650ESP Скачать руководство пользователя страница 18

Страница: 18 / 32

system features learn routine

™

The System Features Learn Routine

™

dictates how the unit operates. Due to the number of steps, they have been

broken up into two menus. It is possible to access and change any of the feature settings using the

Valet

/Program switch. However, this process can be greatly simplified by using the optional DEI Bitwriter or

Personal Computer Interface, P/N

996T

. Any of the settings can be changed and then assigned to a particular

transmitter, up to four, a feature called Owner Recognition. Each time that particular transmitter is used to

disarm the system, the assigned feature settings will be recalled. Owner Recognition is only possible when pro-

gramming the unit via the

996T

or the

998T

DEI Bitwriter.

Using the optional DEI Bitwriter or PC Interface, the learn routine may be locked. Make sure the learn

routine is unlocked before programming features. If the siren generates one long chirp when attempting

to program the unit, the learn routine is locked and must be unlocked using the DEI Bitwriter or PC before proceeding.

Open a door.

(The H1/5 GREEN wire or the H1/7 VIOLET wire must be connected.)

Ignition.

Turn the ignition on, then back off: (The H1/9 YELLOW wire must be connected.)

Select a Menu.

Press and

HOLD

the Valet

/Program button: (The Valet

/Program button

must be plugged into the blue port.) After three seconds the siren will chirp once indi-

cating entry to the Basic Features Menu #1. If this is the menu you wish to access, release

the button and go on to step 4. If the button is not released, you will jump to the

Advanced Features Menu #2 and the siren will chirp twice. Once you have selected the

desired menu, release the Valet

/Program button and then go to step four.

Select a Feature.

Press and release the Valet

/Program button the number of times corre-

sponding to the step you wish to change. For example, to access the third feature, press

and release three times. Then press the button once more and

HOLD

it. The siren will chirp

the number of times equal to the step you have accessed.

Program the Feature.

While

HOLDING

the Valet

/Program button, you can toggle the

feature on and off using the remote transmitter. Pressing Button I will select the one chirp

or default setting. Pressing Button II will select the two chirp setting. (See

Transmitter/Receiver Learn Routine

section of this guide.)

NOTE:

The Valet

pulse count feature (2-5) and the Channel three timed output (2-9) have five

possible settings each. Pressing channel 2 will toggle through all the possible settings.

Содержание 650ESP

































Результаты поиска

Содержание 650ESP

Отзывы:

Похожие инструкции для 650ESP

Бренды по названию

Популярные бренды

Python 650ESP, Руководство по установке

Результаты поиска

Содержание 650ESP

Отзывы:

Похожие инструкции для 650ESP

Бренды по названию

Популярные бренды