manualshive.com logo in svg

PVA PC200 Series, Руководство пользователя

Поделиться
Скачать
PVA PC200 Series Скачать руководство пользователя страница 54

PC200  PVA  

 

 

 

Revision G  (2019)

 

54 of 56

 

 

 

Warranty 

PVA Warranty Policy       

         

 

PVA warrants the enclosed product against defects in material or workmanship on all 
components for one year from the date of shipment. 
The warranty does not extend to components damaged due to misuse, negligence, or 
installation and operation that are not in accordance with the recommended factory 
instructions. Unauthorized repair or modification of the enclosed product, and/or the 
use of spare parts not directly obtained from PVA (or from factory authorized dealers) 
will void all warranties. 

All PVA warranties extend only to the original purchaser. Third party warranty claims 
will not be honored at any time. 

Prior to returning a product for a warranty claim, a return authorization must be 
obtained from PVA’s customer service department. Authorization will be issued either 
via the telephone, facsimile, or in writing upon your request. 

To qualify as a valid warranty claim, the defective product must be returned to the 
factory during the warranty period. Upon return, PVA will repair (or replace) all 
components found to be defective in material or workmanship. 

 

(Retain this for your records)

 

 

Product Information:

 

PRODUCT: 

 

       ______________________________ 

SERIAL NUMBER: 

       ______________________________ 

DATE OF PURCHASE

:    ______________________________

 

 

 

 

 

Содержание PC200 Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды