Puretec UF10 Series, Руководство пользователя

Страница: 13 / 20

13 Copyright © Puretec Pty Ltd 2020 UF Series User Guide
GENERAL OPERATION
Plug into an uninterrupted electrical outlet.
Note: the system transformers are not weather resistant and should
be adequately protected. All electrical connections must be connected
accordingly to local codes.
When the system is operating one of two displays will be shown. Pressing
▲ or ▼ button will alternate between the displays. One of the displays is
always the current time of day (to the nearest hour).
The second display is the days remaining until the next regeneration. If the
days remaining is equal to one, a generation will occur at the next present
regeneration time. The user can scroll between displays as desired.
If the system has called for a regeneration that will occur at the present
time of regeneration, the arrow will point to Regen.
OTHER SETTINGS - these have been factory set (only adjust if required)
1 3
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
SET
SET
1 2
SET
SET
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
OR
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
SET SET
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
RETURN TO
NORMAL MODE
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
SET
2
Step 1 : From normal mode, press SET + ▲ buttons simultaneously for 5
seconds and release.
Step 2: Regeneration Time: Set the clock to the hour the regeneration
should occur by using the ▲ or ▼ buttons. Once the hour is chosen,
press SET and repeat for MINUTES. Factory setting is 2 AM.
Press SET to go to STEP 3.
Step 3: Days to regeneration: This is factory set to 1 (1 days between
regeneration). The allowable range is 1 to 99. Refer to "Regeneration" to
set correct regeneration days.
Press SET to exit Installer Displays and Settings.
The system is factory set to regeneration at 2 AM. If there is a demand for
water when the system is regenerating, untreated water will be used.
SET TIME OF DAY
Step 1 : Press SET for 5 seconds
Step 2:
Current time: set HOUR by using the ▲ + ▼ button then press
SET. Repeat for MINUTES.
After a power outage, the time of day will need to be reset.
Programming
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
SET
SET
Time - Hour
PM
Days To Regen Regen
Min. Fill
Regen
Hour
An arrow points to the
word Regen if a regenera-
tion is expected ‘Tonight’.
POWER LOSS
If the power goes out current time of day will need to be reset. If the
power goes out while the system is regenerating, the cycle picks up where
it was interrupted when the power returns.
Note: The display will flash if a power outage has occurred.
MANUAL REGENERATION
Sometimes there is a need to regeneration the system sooner than when
the system calls for it, usually referred to as a manual regeneration. There
may be a period of heavy water usage because of guests or a heavy
laundry day.
To initiate a manual regeneration at the preset delayed regeneration time,
simultaneously press ▲ + ▼ buttons together and release. The arrow will
point to the word Regen if a regeneration is expected ‘tonight’. To cancel
the regeneration simultaneously press ▲ + ▼ buttons and release.
To initiate a manual regeneration immediately, simultaneously press ▲
+ ▼ buttons together for 3 seconds. The system will begin to regenerate
immediately. The request cannot be cancelled.
REGENERATION MODE
When the system begins to regeneration, the display will change to
indicate the cycle of the regeneration process that is occurring and an
arrow will also point to regen. The system will run through the steps
automatically and will reset itself to provide treated water when the
regeneration is completed.