PumpSpy PS2000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 8

PumpSpy PS2000 Скачать руководство пользователя страница 6

© PumpSpy Technology, LLC Questions?

Email Tech Support:

[email protected]

Your PumpSpy system, once online, connects to PumpSpy’s Remote Monitoring Service. PumpSpy watches
over your system automatically, 24 hours a day. PumpSpy collects operating data on your sump pumps and

battery and analyzes this information to make sure your pumps are always in top working condition.

IF A PROBLEM WITH YOUR MAIN SUMP PUMP, BACKUP PUMP OR BATTERY IS

DETECTED AT ANY TIME, THE PUMPSPY SYSTEM WILL IMMEDIATELY SEND AN

ALERT TO THE PUMPSPY APP.

YOU SHOULD COMPLETE ALL PLUMBING AND INSTALLATION BEFORE

CONNECTING YOUR SYSTEM TO WIFI!

The PumpSpy App is available for Android and Apple iOS devices.

CONNECT YOUR SYSTEM TO WIFI AND

THE PUMPSPY MONITORING SERVICE

STEP 1:

Download and Install the PumpSpy App from the

App Store or Google Play, depending on your device.

STEP 2:

Open the app and create a new PumpSpy Account.
• After entering your info, press Done.
• Press the home button on your Apple/Android device.

STEP 3:

Make sure the PumpSpy System is in WiFi Setup Mode
• The WiFi LED light on the system

should be yellow (setup mode).

• If the WiFi LED is not yellow, gently press and hold the WiFi

setup button using a pencil/paper clip. The unit will turn

yellow/enter setup mode after 3 seconds.

STEP 4:

Connect to the PumpSpy System
• On your Apple/Android device, open Settings.
• Select WiFi.
• Select the WiFi network named “PumpSpy.”
• Press the home button on your Apple/Android device.

STEP 5:

Enter your WiFi Network Credentials
• Open the PumpSpy app.

• The PumpSpy app will ask your permission to send you notifications. Click

OK.

•  Select your WiFi network from the list of available networks.
•  Enter the password for the selected WiFi network and press Done.
•  The Wi-Fi LED will turn red for several seconds, then green once

successfully connected to PumpSpy servers. If it stays red after 60

seconds, start over. (Make sure you enter the correct Wi-Fi password!)

• A Success message will be displayed once connected. Press OK.
• Continue the setup process on the app by entering the location of the

PumpSpy Backup System.

STEP 6:

Enter Alert Contacts
• On the PumpSpy App, select Contacts.
• Following the onscreen prompts, enter cell phone numbers and/or email

addresses that should receive PumpSpy alerts.

2.

6.

RED LED

Offline/Attempting

to Connect

4.

1.

PumpSpy

YELLOW

LED

3.

GREEN

LED

5.

ACTIVATING YOUR PUMPSPY WIFI CONNECTED BACKUP SYSTEM

«
...
4
5
6
7
8
»

Содержание PS2000









Отзывы:

Нет отзывов