manualshive.com logo in svg

Pulsar FLOWPULSE, Инструкция по эксплуатации

Поделиться
Скачать
Pulsar FLOWPULSE Скачать руководство пользователя страница 55

PULSAR MEASUREMENT 

 

55  

 

Simulated Flow 

Simulated flow can be used to test the device output and response.  Using 
the Manual Setting: 

1.

 

Set register 288 to value 1 to turn on simulated flow. 

2.

 

Set register 289 to the flow value in units of millimetres/second flow 
speed. 

3.

 

Turn off simulated flow by setting register 288 to 0. 

Simulated flow overrides actual flow and must therefore be turned off when 
not required.   

Saving & Loading Device Parameters 

For a device which parameters are heavily customised, the user may wish to 
replicate such customisation on a second device.  Saving and loading 
parameters can be used to avoid having to set-up the parameters 
individually again: 

1.

 

Connect FlowPulse PC to the first device, then select System->Save 
Device Parameters. 

2.

 

A confirmation message will appear, and the parameters saved to a 
file within the default folder (use Info->Data Folder Path to see the 

folder location).  The filename is prefixed by “ParamFlowPulse

-

” 

followed by the date and time. 

3.

 

Connect FlowPulse PC to the second device on which to load the 
parameters.  Select System->Load Parameters to Device, then 
choose the parameter file to load. 

Reconnect FlowPulse PC to see new parameter values. 

 

 

 

 

 

 

Содержание FLOWPULSE


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды