manualshive.com logo in svg

Pulsar FLOWPULSE, Инструкция по эксплуатации

Поделиться
Скачать
Pulsar FLOWPULSE Скачать руководство пользователя страница 36

FLOWPULSE INSTRUCTION MANUAL 
 

36 

Setup Menu 

This menu enables setting up of the RS232 port.  The default setting when 
interfacing using FlowPulse PC is 57600 Baud 8bits-No Parity-1Stop bit.   
There is normally no need to change this as FlowPulse PC should 
automatically detect a FlowPulse connected however a specific comport can 

be selected in the ‘Serial Port’ sub menu.

 

The ‘Recording Interval’ menu controls the time interval before a new flow 

record and trace is saved to file when the save-to-feature is in use.  

The ‘Clear Flow Record Chart’ option allows the Flow Record chart to be 

cleared. 

The ‘Work Folder’ allows the setting of a default folder for data files to be 

saved. 

System Menu 

This menu provides the option to perform the following actions: 

OPTION 

DECRIPTIONS 

Save Device Parameters 

Extract configuration parameters from the device 
and save onto PC as a parameter file.  This is saved 

to FlowPulse PC’s installation folder and the 
filename is prefixed with “ParamFlowPulse

-

”.

 

Load Parameter to Device 

Load the parameters from a parameter file onto 
FlowPulse.  This should only be used with a file 

that has a prefix of “ParamFlowPulse

-

”

 

Bootloader Control 

Launch the Bootloader PC program for connecting 
to FlowPulse

’s Bootloader.  This allows the 

firmware on FlowPulse to be upgraded.  Note that 
any customised parameters will be erased during a 
firmware upgrade, and therefore it is 
recommended that device parameters are saved 
onto PC before performing a firmware upgrade. 

Reset Device to Bootloader 

Reset FlowPulse into Bootloader mode.  The 
Bootloader PC program must be used to connect 
to FlowPulse in this mode.  FlowPulse will resume 
normal operation if no connection is established 
within 30 seconds. 

Parameter Factory Reset 

This results all parameters to factory default. 

Содержание FLOWPULSE


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды