background image

 

 

 

1.0  Conventions 

 

For the remainder of this bulletin, the following conventions are in effect. 

 

 

A

 WARNING DEFINES A CONDITION THAT COULD CAUSE DAMAGE TO BOTH 

THE EQUIPMENT AND THE PERSONNEL OPERATING IT

.

 

T

HIS MANUAL MUST 

BE CONSULTED IN ALL CASES WHERE THE 

W

ARNING 

S

YMBOL IS MARKED IN 

ORDER TO FIND OUT THE NATURE OF THE POTENTIAL 

HAZARDS

 AND ANY 

ACTIONS WHICH HAVE TO BE TAKEN TO AVOID THEM

 

CAUTION,

 

POSSIBILITY

 

OF

 

ELECTRIC

 

SHOCK 

 

 

Notes are general information meant to make operating the equipment 
easier.

 

For information on overall pump operation and maintenance, refer to 

the  Installation, Operation, and Maintenance manual specific to the model 
of pump in  question.  The information in this bulletin pertains only to the 
PULSAlarm®   leak  detection system supplied as an option on Pulsafeeder 
PULSA/PULSAPRO/PULSAR Series pumps 

 

 

Tips have been included within this bulletin to help the operator run the 

equipment in the most efficient manner possible. These “Tips” are drawn 
from the knowledge and experience of our staff engineers, and input from 
the field. 

 

2.0  Foreword 

 

The equipment to which these instructions refer is designed for use in industrial areas 
and therefore cannot be treated as retail products.  The present documentation gives 
instructions to be used by qualified personnel only.  It must be used in compliance with 
the regulations, laws and technical standards in force and cannot, under any 
circumstances, take the place of plant standard or additional regulations, including any 
which are not legally enforceable, which have been issued with the scope of ensuring 
safety.  

 

Equipment with special manufacturing or constructive variances may differ in detail with 
respect to this description. 

 

In case of any difficulty, please contact Pulsafeeder, Inc. Technical Service, email at 
[email protected]

 

The PULSAlarm® Switch Assembly is rated for NEMA 7 locations as identified on the 
nameplate.  The PULSAlarm® Switch Assembly complies with both ATEX and IEC IECEx 
standards.  

 

Содержание PULSAlarm Pulsa Series



















Отзывы: