background image

i

Notice Page

TM-1402 Series Progressive Scan Shutter Camera

Notice

The material contained in this manual consists of information that is proprietary to JAI PULNiX, Inc., and may only be used 
by the purchasers of the product. JAI PULNiX, Inc. makes no warranty for the use of its product and assumes no responsibility 
for any errors which may appear or for damages resulting from the use of the information contained herein. JAI PULNiX, Inc. 
reserves the right to make changes without notice.

Microsoft, Windows 95,  98, NT, 2000, XP, and Windows Explorer are either registered trademarks or trademarks of 
Microsoft Corporation in the United States and/or other countries.

Warranty

Please contact your factory representative for details about the warranty.

Certifications

CE Compliance

The TM-1402 series of cameras has been certified to conform to the requirements of Council Directive 89/336/EC for electro-
magnetic compatibility and to comply with the following European Standards:

EMC

EN55022: 1998 + A1: 2000 CLASS A
EN55024: 1998 + A1: 2001

All JAI PULNiX products bearing the CE mark have been declared to be in conformance with the applicable EEC Council 
Directives. However, certain factory-installed options or customer-requested modifications may compromise electromagnetic 
compatibility and affect CE compliance. Please note that the use of interconnect cables that are not properly grounded and 
shielded may affect CE compliance.

Contact the JAI PULNiX Applications Engineering Department for further information regarding CE compliance.

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Oper-
ation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct 
the interference at his own expense.

WARNING

 

Changes or modifications to this unit not expressly approved by the party responsible for 

FCC compliance could void the user’s authority to operate the equipment.

TM-1402 Series Operation Manual

JAI PULNiX, Inc.

1330 Orleans Drive
Sunnyvale, CA 94089
Tel:(408) 747-0300 
Tel:(800) 445-5444
Fax:(408) 747-0880
E-mail: [email protected]

www.jaipulnix.com

A

SS

OCIATIO

N

A

UT

OM

ATED IMA

G

IN

G

MEMBER

R

E

G

IS

TERED

FI

R

M

UL

®

JAI PULNiX, INC.

ISO-9001

FILE #

A3942

Содержание TM-1402 series














































Отзывы: