PSG CADDY ALTERNA Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 54

background image

26

2.9

INSTALLING THE LCD USER INTERFACE

The LCD user interface (touchscreen) is used for the system’s operation. In order to secure it, you need to install the
LCD user interface support using two screws (two holes are designed for this installation on the furnace). The LCD
user interface support and the two screws are supplied with the owner’s manual.

The LCD user interface must be secured to the support. Then, connect the main control board to the LCD user
interface. In order to do so, use the white cable already connected to the main control board and pushes this cable
through the hole above the access panel to the main control board. Simply run the cable along the side of the
furnace using the plastic clips supplied with the owner’s manual as shown below. Secure the access panel to the
main control board back in place. Please note that the LCD user interface is removable if access is limited.

PLASTIC
CLIPS

WHITE WIRE
TELCO WIRE

LCD user
interface support

«
...
24
25
26
27
28
...
»

Содержание CADDY ALTERNA























































Отзывы:

Нет отзывов

Похожие инструкции для CADDY ALTERNA

Бренд: Ingersoll-Rand Страницы: 104

Бренд: Lennox Страницы: 8

Aero Bella AB-716-QH

Бренд: Pinnacle Страницы: 5

Бренд: Maytag Страницы: 58

Бренд: kozy heat Страницы: 33

Condensing Oil-Fired Furnace

Бренд: Adams Страницы: 25

PowerHeat 980 Pro CHH-980

Бренд: Quest Engineering Страницы: 30

(F/G)9MAE0601714A

Бренд: ICP Страницы: 39

Бренд: ICP Страницы: 42

Бренд: ICP Страницы: 52

Бренд: ICP Страницы: 52

Condensing gas furnaces

Бренд: Kenmore Страницы: 36

Бренд: Magnum Страницы: 44

Бренд: Nordyne Страницы: 28

Бренд: Stelpro Страницы: 14

All Residential Multi-position Gas Furnaces

Бренд: Johnson Controls Unitary Products Страницы: 6

Бренд: Johnson Controls Unitary Products Страницы: 8

COMFORT-AIRE EB Series

Бренд: Johnson Controls Unitary Products Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды