Protocol Propaq 242 Скачать руководство пользователя страница 105

Страница: 105 / 120

Propaq CS Directions for Use

105

Ref

erence

Temperature Specifications

Pulse Oximetry (SpO

) Specifications

Characteristic

Specification

Range

0° to +50°C; 32° to +122°F

Displays

T1, T2, and

∆

Probes

Compatible with YSI Series 400 and 700 probes. HP side panel only
compatible with YSI 400 and has HP connector.

Units

°C and °F selectable

Channel Accuracy

Temperature Range

Tolerance

0° to +10°C

±0.2°C

>10° to +50°C

±0.1°C

+32° to +50°F

±0.4°F

>50° to +122°F

±0.2°F

Resolution

0.1°C or °F

Electrosurgery interference
suppression

Included in all models.

Characteristic

Specification

Range

0% to 100%

Probe Accuracy
(specified at 28° to 42° C)

Adults:
70% to 100% ±2 digits
50% to 69% ±3 digits
0% to 49% unspecified

Pediatrics:
70% to 100% ±3 digits

Neonates:
70% to 95% ±3 digits

Pulse Rate Range

25 to 250 beats per minute

Pulse Rate Accuracy

±3 beats per minute or 3%, whichever is greater

Sensor Compatibility

Compatible only with NELLCOR sensors listed in the Protocol
Systems Products and Accessories booklet.

Electrosurgery interference
suppression

Included in all models.

Alarm Hold-Off Time Period

10 seconds; reset if the sensor reports levels within limits before 10
seconds elapses.

Содержание Propaq 242

























































































































Результаты поиска

Содержание Propaq 242

Отзывы:

Похожие инструкции для Propaq 242

Бренды по названию

Популярные бренды

Protocol Propaq 242, Инструкция по применению

Результаты поиска

Содержание Propaq 242

Отзывы:

Похожие инструкции для Propaq 242

Бренды по названию

Популярные бренды