ProSoft Technology ProLinx DNPS Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 86

background image

ProLinx DNPS

♦

ProLinx Gateway

Reference

DNP 3.0 Slave

User Manual

Page 50 of 86

ProSoft Technology, Inc.

December 1, 2009

3.3 Functional

Overview

The DNP 3.0 Slave protocol driver exists in a single port (DNPS) implementation
only. The DNPS port operates in a slave mode only, supporting the DNP 3.0
protocol in a Level 2 implementation.

The DNP slave driver is implemented in ProLinx modules to interface DNP
master units with a variety of communication protocols and interfaces. This driver
supports DNP version 3.0, subset level 2. The Reference chapter of this
documentation contains the Device Profile for the driver. The Reference chapter
contains the subset definition for the driver. This document serves as the base
for understanding the DNP slave driver functionality and configuration. The
discussion is general in nature deferring specifics to the individual product
documents.

Before attempting to use this or any other DNP protocol device, verify that you
have a copy of the DNP Basic 4 document and other information available
through the DNP User Group. It is very important that these documents be
understood for successful application of the protocol in a user’s solution. If you
are a member of the user group, you can download these documents from the
http://www.dnp.org (http://www.dnp.org) Web site.

The DNP slave driver will respond to requests from a remote DNP master device.
All data in the module’s database configured as DNP data points is available to
the remote master device for read and write requests.

3.3.1 DNP 3.0 Slave Port

ACT

ERR

Port 1

ACT

ERR

Port 2

ACT

ERR

Port 3

ACTIVE

ERR

Port 0

ACTIVE

ERR

Debug

ACT

ERR

ACT

ERR

Port 1

ACT

ERR

ACT

ERR

Port 2

ACT

ERR

ACT

ERR

Port 3

ACTIVE

ERR

Port 0

ACTIVE

ERR

Debug

The ProLinx module supports the DNP 3.0 protocol as a Slave on one port. This
port is fully configurable.

«
...
48
49
50
51
52
...
»

Содержание ProLinx DNPS























































































Отзывы:

Нет отзывов

Похожие инструкции для ProLinx DNPS

Touchstone TG1652

Бренд: Arris Страницы: 44

Modular IoT Gateway

Бренд: Volansys Страницы: 26

Бренд: Digi Страницы: 6

Бренд: Matrix Telecom Страницы: 32

MultiVOIP MVPFX2-8

Бренд: Multitech Страницы: 8

Бренд: RTA Страницы: 81

Бренд: DAE Страницы: 2

Бренд: Samson Страницы: 72

Бренд: Bticino Страницы: 4

Бренд: Plugwise Страницы: 28

Бренд: Meraki Страницы: 11

Бренд: Hewlett Packard Enterprise Страницы: 26

Бренд: Aluratek Страницы: 63

Бренд: Zoom Страницы: 54

Бренд: Zoom Страницы: 87

WiSenMeshWAN 6003

Бренд: Wisen Страницы: 11

Бренд: Galaxy Страницы: 18

Бренд: Bpt Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды