ProSoft Technology ProLinx DNPS Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 86

background image

ProLinx DNPS

♦

ProLinx Gateway

Diagnostics and Troubleshooting

DNP 3.0 Slave

User Manual

Page 36 of 86

ProSoft Technology, Inc.

December 1, 2009

2.2.3 4101 Series LEDs

LED State

Description

Off

Power is not connected to the power terminals.

Power

Green Solid

Power is connected to the power terminals. Verify that the other LEDs
for operational and functional status light.

Off Normal

operation.

Fault

Red Solid

The Debug/Configuration mode is active (applies to gateways that
support pass-through on Debug port - such as DFCM units).

If CFG LED is not on, a critical error has occurred. Program executable
has failed or has been user-terminated and is no longer running. Press
Reset p/b or cycle power to clear error. If not, use the Debug
procedures described later in this manual.

Off Normal

operation.

CFG

Amber Solid

If Fault LED is on, the Debug/Configuration Mode is active (if the
gateway supports pass-through on the Debug port - such as DFCM
units).

If the Fault LED is off, the unit is in the configuration mode. The
configuration file is being read and the unit is implementing the
configuration values and initializing the hardware. This will occur during
power cycle, or after pressing reset button. It also occurs after a
cold/warm boot command is received.

Off Normal

operation.

Flashing

An error condition has been detected and is occurring. Check
configuration.

ERR

Solid Red

This condition is indicative of a large number of errors in the application
interface communications. The gateway's error flag is cleared at the
start of each command (master/client) or receipt of data
(slave/adapter/server).

2.3

Serial Port DNPS Error and Status Data

The second and most thorough troubleshooting method for debugging the
operation of the DNPS driver (and the module in general) is the powerful Debug
port on the module which provides much more complete access to the internal
operation and status of the module. Accessing the Debug capabilities of the
module is accomplished easily by connecting a PC to the Debug port and loading
a terminal program such as ProSoft Configuration Builder or HyperTerminal.

Note:

4101 series modules that use both serial ports (Debug and Port x) as application ports (for

example, 4101-MCM-DFCM) must be reset or power-cycled in order to enable the selected port as
a Debug port. To enable the debug port, connect to the port using a null-modem serial cable, and
then press and hold the

[A]

key on the keyboard while resetting or power cycling the card. Do not

release the key until HyperTerminal shows the debug port menu. Debug mode can be enabled on
either port. The upload/download command is only available when connected to the Debug port.

«
...
34
35
36
37
38
...
»

Содержание ProLinx DNPS























































































Отзывы:

Нет отзывов

Похожие инструкции для ProLinx DNPS

Бренд: Pathport Страницы: 3

Бренд: Pace Страницы: 2

Бренд: Farfisa Страницы: 12

iO-GridM GFGW-RM02N

Бренд: DAUDIN Страницы: 28

Бренд: M2M Страницы: 357

Бренд: MediaAccess Страницы: 68

Touchstone TG862G

Бренд: Arris Страницы: 48

ThingPark Partner

Бренд: Actility Страницы: 4

Бренд: Smartenit Страницы: 2

Бренд: NETGEAR Страницы: 25

Бренд: NETGEAR Страницы: 2

RouteFinder RF550VPN

Бренд: Multi-Tech Страницы: 76

Бренд: Essential Trading Страницы: 15

NXB-CCG-K NetLinx Clear Connect

Бренд: AMX Страницы: 2

Бренд: AMX Страницы: 5

NetLinx NXR-ZGW

Бренд: AMX Страницы: 42

NetLinx NXR-ZGW-PRO

Бренд: AMX Страницы: 46

Бренд: Schwaiger Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды