ProSoft Technology ProLinx DNPS Скачать руководство пользователя страница 33

Страница: 33 / 86

Diagnostics and Troubleshooting

ProLinx DNPS

♦

ProLinx Gateway

User Manual

DNP 3.0 Slave

ProSoft Technology, Inc.

Page 33 of 86

December 1, 2009

This action opens the

IAGNOSTICS

dialog box.

Press

[?]

to open the Main Menu.

Important:

The illustrations of configuration/debug menus in this section are intended as a general

guide, and may not exactly match the configuration/debug menus in your own module.

If there is no response from the module, follow these steps:

Click to configure the connection. On the Connection Setup dialog box, select
a valid com port or other connection type supported by the gateway.

Verify that the null modem cable is connected properly between your
computer’s serial port and the module. A regular serial cable will not work.

On computers with more than one serial port, verify that your communication
program is connected to the same port that is connected to the module.

Содержание ProLinx DNPS























































































Результаты поиска

Содержание ProLinx DNPS

Отзывы:

Похожие инструкции для ProLinx DNPS

Бренды по названию

Популярные бренды

ProSoft Technology ProLinx DNPS, Руководство пользователя

Результаты поиска

Содержание ProLinx DNPS

Отзывы:

Похожие инструкции для ProLinx DNPS

Бренды по названию

Популярные бренды