Prosense PPS Manager Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 25

Prosense PPS Manager Скачать руководство пользователя страница 23

23

PRS-UM-PPSM-EN-Rev.03-10.04.2020

If the alarm stops and the reason for the alarm is identified and resolved (e.g. a kitchen burner lit off
but in the open position) the gas supply may be re-opened after checking that all the gas appliances
are off.

8.

FAULT CODES

PPS panel will display the fault code when an fault condition detected. Press up and down arrow
buttons to see fault codes while fault status raised and fault LED activated:

Here the code details that can help to understand problem and find a resolution:

Fault

Code

Details

10

EFuse Dedektor Power Line Fault

11

No detector installed on zone module

12

Detector in fault status. Either detector raising a fault status or communication to detector

interrupted

13

CO gas selected for detectors but there is no CO detector installed on zone module

14

NO2 gas selected for detectors but there is no NO2 detector installed on zone module

15

LPG gas selected for detectors but there is no LPG detector installed on zone module

Table 8. Fault codes and details

Error 12

«
...
21
22
23
24
25
»

Содержание PPS Manager


























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды