PRONAR T386 Скачать руководство пользователя страница 85

Страница: 85 / 162

SECTION 4

Pronar T386

4.17

Make sure that the hitching operation was completed and the second

trailer drawbar is secured.

Connect conduits of pneumatic, hydraulic and electrical systems according to

instructions contained in section (4.3)

Unhitching the second trailer

Immobilise tractor and trailers with parking brake.

Turn off tractor engine. Ensure that unauthorised persons do not have access

to the tractor cab.

Disconnect conduits of pneumatic, hydraulic and electrical systems according

to instructions contained in section 4.3.

Unlock the pin of the rear hitch of the first trailer. Remove drawbar pin and

drive tractor away.

DANGER

When hitching/unhitching the trailer, there must be nobody between the trailers. Person
assisting hitching up machines should stand outside the area of danger and be visible to
the tractor driver at all times.

WARNING

Do NOT hitch a second trailer constructed on any chassis except dual axle chassis.

Содержание T386



































































































































































Результаты поиска

Содержание T386

Отзывы:

PRONAR T386, Руководство оператора, Страница: 85 / 162

Результаты поиска

Содержание T386

Отзывы: