PRONAR T386 Скачать руководство пользователя страница 154

Страница: 154 / 162

Pronar T386

SECTION 5

5.44

FAULT

REASON

REMEDY

Excessive cylinder loading

Check mechanism controlled by
cylinder for mechanical damage

Damaged hydraulic
conduits

Check and ascertain that hydraulic
conduits are tight, not fractured
and properly tightened. If
necessary, replace or tighten

Hydraulic system conduits
are not connected or
connected incorrectly

Check the connection and connect
the leads according to the
Operator's Manual

The electrical system for
controlling the trailer is not
connected

Check the connection and connect
the leads according to the
Operator's Manual

Control panel is switched off Switch control panel on

Control panel is damaged

Repair at an authorised service
point

Damaged hydraulic quick
couplers

Replace

Insufficient quantity of
hydraulic oil in tractor's
hydraulic system

Use the tractor having hydraulic oil
output compatible with the oil
demand of the trailer.

Faulty inductive sensor

Check according to chapter 5.4,
replace if necessary

Tipping / pulling the load
box on / removing the
load box from the trailer is
not possible

Damaged actuator module

Repair at an authorised service
point

Jerking, uneven trailer
braking

Damaged or unconnected
brake system supply
conduit

Check conduit, check connection
socket. Repair, change or connect
conduit.

Incorrect operation of a
hydraulic steering system

Insufficient working
pressure

Check pressure on pressure
gauges and set at required value

No lighting

Electrical system is not
connected

Connect electrical system

Содержание T386



































































































































































Результаты поиска

Содержание T386

Отзывы:

PRONAR T386, Руководство оператора, Страница: 154 / 162

Результаты поиска

Содержание T386

Отзывы: