manualshive.com logo in svg

PRONAR NV161/1, Руководство оператора

Поделиться
Скачать
PRONAR NV161/1 Скачать руководство пользователя страница 57

SECTION 3 

Pronar NV161/1 

│ 

NV161/2 

│ 

NV161/3

│ 

NV161/4 

│ 

NV161/5 

3.13 

The system is equipped with two cut-off valves (3) which are used for protecting the tailgates 

against  opening  during  transport  and  for  independent  setting  of  the  tailgates  to  limit  the 

spreading width during fieldwork. 

 

ATTENTION 

 

Hydraulic conduits of the tailgate opening system are marked with green plugs. 

During  maintenance  work  with  the  tailgates  open,  protect  them  from  falling  down  by 
closing  the  cut-off  valve  and  with  a  suitable  mechanical  support  which  is  durable  and 
stably mounted. 

Take special care not to close or open the tailgates when they are locked by means of 
cut-off valves. Otherwise, hydraulic cylinders and/or tailgates may be damaged. 

 

3.2.7  HYDRAULIC SYSTEM OF THE SLIDE GATE 

Pronar  manure  spreader  can  be  equipped  with  a  load  box  slide  gate.  The  slide  gate  is 

mounted in front of the spreader unit and it ensures safe transport of disintegrated materials 

(e.g. compost, peat) on public roads and ensures safe start of disintegrating wormshafts. 

The load box slide gate is controlled hydraulically. This hydraulic system is supplied from the 

external hydraulic system of the tractor. The hydraulic cylinders opening and closing the slide 

gate are controlled by means of the manifold in the tractor cab. Oil pumped under pressure 

from the tractor external hydraulic system through a supply conduit (5) enters the flow divider 

(3) which separates the oil stream proportionally to the two hydraulic cylinders (2) causing the 

cylinder rods move steadily upwards to open the slide gate (1). 

The slide gate is closed by changing the position of the manifold lever in the tractor. Then, oil 

is  pumped  through  conduit  (4)  to  cylinders  (2).  Consequently,  the  cylinder  rods  are  moved 

downwards and the slide gate is closed. 

ATTENTION 

 

Hydraulic conduits of the slide gate's hydraulic system are marked with red plugs. 

 

Содержание NV161/1





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды