Promise Technology FastTrak TX4310 Скачать руководство пользователя страница 13

Страница: 13 / 134

Chapter 1: Introduction

Specifications

•

Low-profile printed circuit board

•

PCI Slot 33 MHz or 66 MHz

•

Controller card dimensions (H x W): 2.25 x 4.75 inches (57 x 121 mm)

•

Operating temperatures: 32

to 122

F (0

C to 50

•

Operating humidity: 5% to 95% non-condensing

Complies with Serial ATA II:
Extensions to Serial ATA 1.0a
Specification

Provides enclosure and drive monitoring
compatibility.

Compliant with PCI Bus
Master standard. PCI Bus
Master support

Provides 32-bit I/O and, Bus Master, and Serial
ATA performance for optimal system
performance.

Tested compatibility to coexist
with motherboards that have
integrated IDE controllers

Improves system performance and minimizes
system conflicts for new and existing
installations.

Compatible with all major
SATA generation 1 and SATA
generation 2, phase 1 and
phase 2 disk drives

Promise performs verification testing with major
drive manufacturers and development partners.

Features LBA support

Supports drives greater than 137 GB capacity.

Supports BIOS Boot
Specification

All disk arrays attached to the FastTrak card
appear in the BBS-compliant motherboards
BIOS boot list.

Compatible with Promise
SuperSwap enclosures

Provides enclosure management including fan,
temperature and voltages.

Compatibility

Features

Benefits

Содержание FastTrak TX4310







































































































































Результаты поиска

Содержание FastTrak TX4310

Отзывы:

Promise Technology FastTrak TX4310, Руководство пользователя, Страница: 13 / 134

Результаты поиска

Содержание FastTrak TX4310

Отзывы: