Promate PH1500 Скачать руководство пользователя страница 9

PERIODIC MAINTENANCE

ITEM

NOTES

Daily (Before 

operation)

Initial

20 hours

Every 

50 hours

Every

100 hours

Spark Plug

Check condition. Adjust gap and clean. 

Replace if necessary.

Engine Oil

Check oil level.

Replace

.

Air Filter

Clean, replace if necessary.

Fuel Filter

Clean fuel filter and fuel tank strainer.

Replace if necessary.

Fuel Line

Check fuel hose for cracks or other 

damage. Replace if necessary.

Exhaust

System

Check for leakage. Retighten or 

replace gasket if necessary. 
Check muffler screen. Clean/

replace if necessary.

Carburetor

Check choke operation.

Starting 

System

Check recoil starter operation.

Fittings/

Fasteners

Check. Replace if necessary.

CAUTION

MAINTENANCE

SPARK PLUG

Remove the spark plug and clean the electrodes 

section with a wire brush or sandpaper. Next, set 

the gap at .028/.031 inches (0.7-0.8 mm) by 

adjusting the negative electrode. Replace the spark 

plug with correct torque: 14 ft-lb (20 N.m)

Replace with only the same type of spark plug 

which was removed. An improper spark plug can 

cause the engine to overheat, emit smoke, or 

otherwise perform poorly.

OIL TYPE

Use new good quality oil, SE, SF, or SD grade. The 

oil to be used depends upon the temperature at 

which the engine is operated:

Below 32°'b0 F (0°'b0 C)- SAE 10W, 10W-30, or 10W-40

32 to 80°'b0 F (0 to 25°'b0 C) -SAE 20W, 10W-30, or 10W-40

80 to 95°'b0 F (25 to 35°'b0 C) -SAE 30W, 10W-30, or 10W-40

Above 95°'b0 F (35°'b0 C) -SAE 40W

OIL REPLACEMENT

1. Change oil while engine is warm.

2. Place the generator unit on a level surface.

3. Remove the oil filler cap.

4. Open the oil drain plug and let oil drain

completely into a pan placed under the

engine.

5. Check gaskets. Replace if required.

6. Reinstall the oil drain plug and refill engine

with clean oil.

7. Replace the oil filler cap.

9

Содержание PH1500














Отзывы: