Progressive Turf Equipment TDR-X Скачать руководство пользователя страница 35

Страница: 35 / 75

TDR-X

Operator’s Manual

DRIVELINE GREASING

All PTO shafts on the TDR-X mower feature 100h greasing intervals.
The following decal is located on the mower as a reminder.

Failure to properly lubricate the telescoping shaft sections will lead to
binding of the shaft and damage to the mower or tractor driveline.

INPUT SHAFT

– 100h / Monthly (10 Locations)

Shaft must be disconnected from tractor and collapsed fully for greasing

INTERMEDIATE SHAFT

– 100h / Monthly (3 Locations)

DECK SHAFTS

– 100h / Monthly (7 Locations - 3 Shafts

)

CROSS & BEARINGS

C.V. CENTER HOUSING

C.V. BALL & SOCKET

TELESCOPING SHAFT*

GUARD BUSHINGS

CROSS & BEARINGS

INPUT

SPLINE

CROSS & BEARINGS

SLIP YOKE SPLINES

GUARD BUSHINGS

* Inner & outer guards must be rotated to align holes for accessing the two telescoping shaft grease fittings.

TELESCOPING SHAFT*

GUARD BUSHINGS

CROSS & BEARINGS

SPLINE

Содержание TDR-X












































































Результаты поиска

Содержание TDR-X

Отзывы:

Похожие инструкции для TDR-X

Бренды по названию

Популярные бренды

Progressive Turf Equipment TDR-X, Руководство оператора и список запчастей

Результаты поиска

Содержание TDR-X

Отзывы:

Похожие инструкции для TDR-X

Бренды по названию

Популярные бренды