Progressive Turf Equipment TDR-X Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 75

background image

TDR-X

Operator’s Manual

3

INTRODUCTION

Thank you for purchasing a TDR-X mower. This product is designed and manufactured to allow safe and
productive mowing of contoured areas. A well-maintained machine will provide years of reliable service.

FOREWORD

Keep this manual with the mower at all times. This manual is intended as a guide to the safe use and
maintenance of the machine, so before you operate this machine, study this manual carefully.

Replace this manual immediately if it becomes lost.

This manual is not considered all-inclusive, so for further information on specific components, e.g. PTO
shafts etc refer to the respective documents included with the manual set for this machine.

The  TDR-X  mower  is  a  contour  roller  turf  grass  finishing  mower  with  a  10.5  foot  cutting  width,  and  is
designed to be pulled by a 35-40 PTO horsepower utility tractor.  These versatile mowers have the ability
to mow both contoured and flat terrain that requires a high quality, finished after cut appearance.  High
blade tip speed leaves a second-to-none after cut appearance. 6-way floating decks, and an Adaptive
Swivel Hitch isolates the tractor from the mower allowing truer contour tracking.

Features:

•

Three independent floating decks

•

Cut height can be set on each deck between 3/8 inch and 3 3/8 inches

•

10.5 foot cutting width

•

Adaptive Swivel Hitch

•

Pro Lift-N-Turn

TM

allows three decks to be temporarily raised slightly off the ground with the

PTO still engaged

•

Automatic mechanical deck locks for transport

Applications:

•

Golf course roughs, fairways and bunker surrounds

•

Corporate and industrial campuses

•

Park lands and recreational areas & sports venues

•

Landscaped venues

TDR Series Mower Application Guide

Model

TDR-X

Soil Type

All (firm



sandy)

Turf Condition

All conditions

Comments

For use in areas where ride-on reel-type mowers cannot be used.

OSHA Training Requirements (USA)

The following training requirements have been taken from Title 29, Code of Federal Regulations Part
1928.57 (a)(6). www.osha.gov

Operator Instructions: At the time of initial assignment and at least annually thereafter, the employer shall
instruct every employee in the safe operation and servicing of all covered equipment with which he is or
will be involved, including at least the following safe operating practices.

In other jurisdictions:

It is good practice, following the initial instruction and at least annually thereafter, that the employer
instruct every employee in the safe operation and servicing of all covered equipment with which he is or
will be involved, including at least the following safe operating practices.

«
...
3
4
5
6
7
...
»

Содержание TDR-X












































































Отзывы:

Нет отзывов

Похожие инструкции для TDR-X

Бренд: Baroness Страницы: 5

Бренд: Jacobsen Страницы: 46

Бренд: Jacobsen Страницы: 70

Бренд: Jacobsen Страницы: 26

Бренд: Jacobsen Страницы: 247

Greens King V Plus

Бренд: Jacobsen Страницы: 94

Groom Master II

Бренд: Jacobsen Страницы: 104

Бренд: Jacobsen Страницы: 144

Бренд: PAPILLON Страницы: 27

FREEDOM Z SFZ36-17KA

Бренд: Scag Power Equipment Страницы: 69

Бренд: Jacobsen Страницы: 148

Бренд: Gardenline Страницы: 28

Бренд: Feider Machines Страницы: 22

Бренд: Texas Страницы: 60

GLM 40/124 P EASY

Бренд: F.F. Group Страницы: 128

911394 - Pro 21SCH

Бренд: Gravely Страницы: 23

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды