Progressive Turf Equipment 13921943 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 62

background image

31

SPINDLE INSPECTION:

Spindles are equipped with two roller ball bearings. Adjustment is set by
tightening the 1” left hand nut to 60 ft-lbs. torque for proper setting.

Periodically inspect blade spindles by grasping blade, and moving from side
to side. If any free play is noted, replace or repair.

SPINDLE ASSEMBLY REMOVAL:

Remove blade from spindle.

Remove belt shield. Loosen 4 bolts that hold gearbox to mount. Loosen
1/2” x 3 1/2” tap bolts and slide gearbox toward front until belt is easy to
remove.

Remove belt.

Remove 4 bolts attaching spindle assembly to mower frame and remove as
a unit, since pulley will come out through the hole in the deck.

SPINDLE ASSEMBLY INSTALLATION:

Reverse above procedure. Be sure spindle mounting area of deck is clean of
any foreign material before attaching spindle assembly.

SPINDLE REPAIR:

Spindle repair requires special skills and tools. If your shop is not properly
equipped or your mechanics are not properly trained in this type of repair,
you may be time and money ahead to use a new spindle assembly.

Remove pulley from spindle assembly. Place assembly in press and force
spindle down through housing. Once pressed apart, replace bearings, as
removal will have damaged bearings internally.

«
...
29
30
31
32
33
...
»

Содержание 13921943































































Отзывы:

Нет отзывов

Похожие инструкции для 13921943

Бренд: Jacobsen Страницы: 46

Бренд: Jacobsen Страницы: 70

Бренд: Jacobsen Страницы: 26

Бренд: Jacobsen Страницы: 247

Greens King V Plus

Бренд: Jacobsen Страницы: 94

Groom Master II

Бренд: Jacobsen Страницы: 104

Бренд: Jacobsen Страницы: 144

Бренд: Yard Machines Страницы: 44

Бренд: Yardworks Страницы: 21

Бренд: Weed Eater Страницы: 48

Бренд: Yard-Man Страницы: 8

Бренд: Garten Meister Страницы: 84

Бренд: Zenoah Страницы: 2

Бренд: Snapper Страницы: 4

Бренд: MTD Страницы: 35

Бренд: Yard-Man Страницы: 6

Бренд: Walker Rider Lawnmowers Страницы: 100

BOXER AGRI FA Series

Бренд: De Heus Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды