Progressive Turf Equipment 13921943 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 62

Progressive Turf Equipment 13921943 Скачать руководство пользователя страница 27

27



Check the properties of the grease you wish to use with your supplier prior to
use

.

LUBRICATION

:

A  properly  maintained  lubrication  schedule  will  provide  a  smooth  running
machine  for  many  years.  All  pivot  locations  have  grease  fittings.    The
following  information  shows  and  describes  where  all  lubrication  points  are
located.

.

DECKS

P.T.O. SHAFTS

FRAME



Spindles* (See Manual)



3 Pivots per Wing
Deck*



2 Pivots on Rear Deck*



Castor Wheel &
Swivels*

*As Required



Main Input*(See
Below)



Deck Drive, 4
Locations per Shaft*



Pull Apart Sliding
Tubes once per week
and lubricate

*As Required



8

Pivot Locations*



2 Wheels*

*As Required

CHECK FOR PROPER OIL LEVEL IN GEAR BOXES DAILY

GREASING SCHEDULE & LOCATION

BLADE SPINDLE GREASING

:

The  top  bearing  on  all  spindle  assemblies  has  a  shield  only.    This  allows
grease  to  exit  and  relieves  any  pressure  build  up  inside  spindle  housing,
when greasing.  Greasing of blade spindles should continue until grease can
be  seen  exiting  between  the  top  bearing  and  the  bottom  of  hub  on  pulley.
Some working conditions will require this operation to take place every 4 to
5  running  hours  because  of  hot  working  areas.    Cooler  working  areas  will
only require greasing every 8 to 10 hours.  A proper greasing schedule can

«
...
25
26
27
28
29
...
»

Содержание 13921943































































Отзывы:

Нет отзывов