Probe PMA-H2000 Скачать руководство пользователя страница 2

Safety Information

This symbol indicates that dangerous voltage 
consisting a risk of electric shock is present within 
this unit.

Warning

Precaution

This exclamation point symbol is intended to alert the 
user to the presence of important operating and 
maintenance (servicing) instructions in the literature 
accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE 

PARTS INSIDE.   REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION:

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.

Be sure to use only the standard adapter that is specified in
the specification sheet. Using any other adapter could cause
fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to the
product.

Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause abnormal heat generation
or fire.

Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.

When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.

Do not place conductive objects (e.g. screw drivers, coins,
metal things, etc.) or containers filled with water on top of
the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.

If any unusual smell or smoke come from the unit, stop
using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use
in such a condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.

When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.

WARNING

WARNING

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

Precautions

Operating

t

 Before using, make sure power supply and others are

    properly connected.
  

t

 While operating, if any abnormal condition or malfunction

    is observed, stop using the camera immediately and then

   

 contact your Special dealer.

Handling

  

t

Do not disassemble or tamper with parts inside the camera.

  

t

Do not drop or subject the camera to shock and vibration as

    this can damage camera.
  

t

Care must be taken when you clean the clear dome cover.

    Especially, scratch and dust will ruin your quality of camera.

Installation and Storage

  

t

Do not install the camera in areas of extreme temperature,

    which exceed the allowable range.
  

t

Avoid installing in humid or dusty places.

  

t

Avoid installing in places where radiation is present. 

  

t

Avoid installing in places where there are strong magnetic

    fields and electric signals.
  

t

Avoid installing in places where the camera would be subject

    to strong vibrations.
  

t

Never expose the camera to rain and water.

Содержание PMA-H2000





























Отзывы: