background image

 

 

Operating instructions LITTY 4you 

 

17

 

 

Figure 28: Cylindrical pin in groove 

 

A spring system on the anti-tippers can be 
used for example to overcome obstacles to 
swivel them 

from the operating to passive 

position 

so that they can't get caught on the 

obstacle. To swivel the anti-tippers away, pull 
them each backwards out of the anti-tipper 
barrels until the cylindrical pin protrudes from 
the grooves and then turn these by 180° up-
wards so that the anti-tipping wheel points 
upwards (Fig. 30). After releasing the anti-
tippers, the cylindrical pin slots into the groove 
again.  

After passing the obstacle, use the same proc-
ess to return the anti-tippers 

from the passive 

to the operating position 

again. Make sure 

that these have clicked back into place again 
properly (Fig. 31). 

 When changing between passive and 

operating position, always turn the anti-tippers 
outwards in the direction of the respective drive 
wheel as otherwise this could damage the 
springs.  

 

Figure 29: Operating and passive position of the 
anti-tippers 

 

 

Figure 30: Move anti-tippers from operating to pas-
sive position 

 

 

Figure 31: Moving anti-tippers from passive to oper-
ating position 

 

 The anti-tippers have exclusively been 

designed to minimize the risk of tipping over 
backwards. They are not suitable for reducing 
the risk of tipping forwards or to the side. There 
are no safety accessories available to minimise 
these risks. For this reason, handling these 
risks need to be learnt in cooperation with your 
therapists and doctors. 

 

 

Passive 
position 

Operating 
position 

Pull out anti-
tippers and turn 
them upwards to 
left or right 

Pull out anti-
tippers and turn 
them downwards 
to left or right 

Cylindrical 
pin in 
groove 

Anti-tipper 
sleeve 

rotate

pull 

rotate 

pull 

Содержание LITTY 4you









































Отзывы: