Pro Spot Hybrid Spot Скачать руководство пользователя

Страница: 6 / 36

2 Safety

Page 5

The Hybrid Spot welder has been designed and is tested to meet strict safety require-

ments. Please read the following instructions carefully before operating the

unit and refer to them as needed to ensure the continued safe operation of the welder.

Information provided in this manual describes the suggested best working prac-

tices and should in no way take precedence over individual responsibilities or

local regulations.

The Hybrid Spot Welder is designed to comply with all applicable safety regulations for

this type of equipment. During operation, it is always each individual’s responsibil-

ity to consider:

Their own and other’s personal safety.

The safety of the welder through correct use of the equipment in accordance

with the descriptions and instructions provided in this manual.

By observing and following the safety precautions, users of the Hybrid Spot

Spot welder will ensure safer working conditions for themselves and

their fellow workers.

The following types of safety signs are used on the equipment and in Pro Spot’s

instruction manuals:

Prohibited.

Prohibits behaviour that

can cause injury.

Caution.

Read instruction manual.

Command.

Calls for a specific action.

Warning.

Notice of personal injury risk and

or damage to equipment.

Warning.

Some parts of the welder may become

hot after prolonged use.

2.2 Warnings and important notices

2.1 General

2.0 Safety & Environmental Specifications

2 Safety

The Hybrid Spot welder is designed for indoor use.

The Hybrid Spot welder is designed to operate from 10º C to 40º C.

Do not operate the unit on a slope of more than 10º.

Attention!

Lire Mode d’Emploi.

Interdit.

Interdit aux comportements

qui peuvent provoquer des blessures.

Commande.

Appelle à une action spécifique.

Avertissement.

Avis de risque de blessure personnelle

et / ou d’endommager l'équipement.

Avertissement.

Certaines parties du soudeur peuvent devenir

chaudes après une utilisation prolongée.

Hybrid Spot

Содержание Hybrid Spot





































Результаты поиска

Содержание Hybrid Spot

Отзывы:

Похожие инструкции для Hybrid Spot

Бренды по названию

Популярные бренды

Pro Spot Hybrid Spot, Инструкция по эксплуатации

Результаты поиска

Содержание Hybrid Spot

Отзывы:

Похожие инструкции для Hybrid Spot

Бренды по названию

Популярные бренды